Mill X-axis Powerfeed for G08689
#24
Got back to working on this, and decided the next step was to wire up the motor. It turns, has loads of torque, and is FAR TOO SLOW! It runs at 70 PRM, which is about 4.375 inches per minute of table travel. That's barely enough for fly cutting, but nowhere near fast enough for rapid movement.

I've been looking at belt driven gears (spare parts for the mill from LMS), gearing and whole new motors. Nothing I've found seems to work like I want. Back to the drawing board.
Full of ideas, but slow to produce parts
Reply
Thanks given by:


Messages In This Thread
Mill X-axis Powerfeed for G08689 - by rleete - 04-22-2023, 03:33 PM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 04-23-2023, 12:38 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 04-23-2023, 07:56 AM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 04-23-2023, 11:16 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 04-24-2023, 11:04 AM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 04-24-2023, 10:28 PM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 04-25-2023, 05:48 AM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 05-04-2023, 03:21 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 05-04-2023, 06:16 AM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 05-04-2023, 08:59 PM
RE: Mill X-axis Powerfeed for G08689 - by Vinny - 05-04-2023, 09:35 PM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 05-04-2023, 10:13 PM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 05-05-2023, 03:39 PM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 05-05-2023, 06:31 PM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 05-11-2023, 03:33 PM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 06-03-2023, 12:51 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 06-03-2023, 07:39 AM
RE: Mill X-axis Powerfeed for G08689 - by BaronJ - 02-28-2024, 09:32 AM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 02-28-2024, 11:53 AM
RE: Mill X-axis Powerfeed for G08689 - by BaronJ - 02-28-2024, 02:27 PM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 02-28-2024, 02:40 PM
RE: Mill X-axis Powerfeed for G08689 - by BaronJ - 02-29-2024, 05:08 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 03-22-2024, 06:17 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 03-22-2024, 10:16 AM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 03-22-2024, 11:32 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 03-23-2024, 05:02 PM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 03-23-2024, 11:40 PM
RE: Mill X-axis Powerfeed for G08689 - by rubes - 03-24-2024, 09:45 AM



Users browsing this thread: 1 Guest(s)