Machining an AR15 lower receiver

Hello There, Guest! Register

Thread Modes

Machining an AR15 lower receiver

Highpower Offline

Offline

JAFO

Posts: 4,369
Threads: 178
Joined: Feb 2012
Location: Missouri, USA

#38

06-29-2012, 08:31 PM

This is the kind of thing that makes me sad though. Bad internet advice. This poor guy was convinced by someone else on another forum that he could successfully do this kind of work with nothing more than a bench top drill press and a Dremel tool. Bash

Bash

[Image: 1229112009.jpg]

[Image: 1230111904.jpg]

[Image: 100_1456.jpg]

[Image: 100_1458.jpg]

Willie

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Machining an AR15 lower receiver - by Highpower - 06-20-2012, 04:35 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 04:38 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 04:39 PM

RE: Machining an AR15 lower receiver - by EdK - 06-20-2012, 04:47 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 04:58 PM

RE: Machining an AR15 lower receiver - by EdK - 06-20-2012, 05:03 PM

RE: Machining an AR15 lower receiver - by doubleboost - 06-20-2012, 04:48 PM

RE: Machining an AR15 lower receiver - by EdK - 06-20-2012, 04:55 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 05:02 PM

RE: Machining an AR15 lower receiver - by stevec - 12-01-2013, 07:28 AM

RE: Machining an AR15 lower receiver - by TomG - 06-20-2012, 05:10 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 05:32 PM

RE: Machining an AR15 lower receiver - by TomG - 06-20-2012, 05:41 PM

RE: Machining an AR15 lower receiver - by ETC57 - 06-20-2012, 06:12 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-20-2012, 07:30 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-20-2012, 09:30 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-21-2012, 01:38 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-21-2012, 12:28 AM

RE: Machining an AR15 lower receiver - by Highpower - 06-21-2012, 12:28 AM

RE: Machining an AR15 lower receiver - by RobWilson - 06-21-2012, 09:12 AM

RE: Machining an AR15 lower receiver - by TomG - 06-21-2012, 01:49 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-21-2012, 04:19 PM

RE: Machining an AR15 lower receiver - by TomG - 06-21-2012, 04:33 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-21-2012, 04:56 PM

RE: Machining an AR15 lower receiver - by doubleboost - 06-21-2012, 03:03 PM

RE: Machining an AR15 lower receiver - by DaveH - 06-21-2012, 03:26 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-21-2012, 07:55 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-21-2012, 09:58 PM

RE: Machining an AR15 lower receiver - by RobWilson - 06-22-2012, 10:51 AM

RE: Machining an AR15 lower receiver - by TomG - 06-21-2012, 10:17 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-22-2012, 12:06 AM

RE: Machining an AR15 lower receiver - by Mayhem - 06-21-2012, 10:30 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-22-2012, 12:27 AM

RE: Machining an AR15 lower receiver - by TomG - 06-22-2012, 06:28 AM

RE: Machining an AR15 lower receiver - by Highpower - 06-22-2012, 08:34 AM

RE: Machining an AR15 lower receiver - by DaveH - 06-22-2012, 09:25 AM

RE: Machining an AR15 lower receiver - by TOM REED - 06-22-2012, 09:36 AM

RE: Machining an AR15 lower receiver - by Highpower - 06-22-2012, 04:29 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-29-2012, 08:31 PM

RE: Machining an AR15 lower receiver - by ScrapMetal - 06-30-2012, 02:24 AM

RE: Machining an AR15 lower receiver - by DaveH - 06-29-2012, 08:38 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-29-2012, 09:19 PM

RE: Machining an AR15 lower receiver - by TomG - 06-29-2012, 08:46 PM

RE: Machining an AR15 lower receiver - by Highpower - 06-30-2012, 10:03 AM

RE: Machining an AR15 lower receiver - by ScrapMetal - 07-01-2012, 01:08 AM

RE: Machining an AR15 lower receiver - by Highpower - 07-01-2012, 08:59 AM

RE: Machining an AR15 lower receiver - by doubleboost - 07-01-2012, 10:49 AM

RE: Machining an AR15 lower receiver - by Highpower - 07-01-2012, 12:23 PM

RE: Machining an AR15 lower receiver - by doubleboost - 07-01-2012, 12:42 PM

RE: Machining an AR15 lower receiver - by NevadaBlue - 07-23-2012, 10:52 AM

RE: Machining an AR15 lower receiver - by Highpower - 07-23-2012, 12:04 PM

RE: Machining an AR15 lower receiver - by d65 - 11-30-2013, 09:49 PM

RE: Machining an AR15 lower receiver - by Highpower - 12-22-2013, 07:26 AM

Users browsing this thread: 1 Guest(s)