The following warnings occurred:
Warning [2] count(): Parameter must be an array or an object that implements Countable - Line: 864 - File: showthread.php PHP 7.4.33 (FreeBSD)
File Line Function
/showthread.php 864 errorHandler->error



MetalworkingFun Forum › Machining › Welding & Casting v
Mill Engine Cylinder Casting

Thread Modes
Mill Engine Cylinder Casting
doubleboost Offline
Super Moderator
******
Posts: 1,459
Threads: 159
Joined: Feb 2012
Location: Northern England
#1
08-12-2012, 02:49 PM (This post was last modified: 08-12-2012, 02:51 PM by doubleboost.)
Hi
Lads
I made use of the sand cores i made last week and cast my cylinder
[Image: IMG_4071.jpg]
This picture shows the sand core in the mould
[Image: IMG_4076.jpg]
The small round bit is where the metal is poured in (sprue) the rectangulsr bit is the riser
This feeds the casting as it cools
[Image: IMG_4077.jpg]

[Image: IMG_4080.jpg]

[Image: IMG_4082.jpg]
This shows where the riser has been cut off (nice clean solid metal)
This is always a welcome sight
[Image: IMG_4085.jpg]
Very happy with it
[Image: IMG_4061.jpg]
I cast this yesterday with poor results
[Image: IMG_4062.jpg]
Nasty void in the riser (scrap casting)
At least you can always cut it up and re melt it

I could not resist machining at least one face
Good clean metal
[Image: IMG_4088.jpg]
[Image: IMG_4091.jpg]
[Image: IMG_4092.jpg]
John
http://www.youtube.com/user/doubleboost
Reply
Thanks given by:


Messages In This Thread
Mill Engine Cylinder Casting - by doubleboost - 08-12-2012, 02:49 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-12-2012, 03:48 PM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-12-2012, 03:51 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-12-2012, 04:10 PM
RE: Mill Engine Cylinder Casting - by Mayhem - 08-12-2012, 11:45 PM
RE: Mill Engine Cylinder Casting - by krv3000 - 08-13-2012, 01:48 AM
RE: Mill Engine Cylinder Casting - by Highpower - 08-13-2012, 07:16 AM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-13-2012, 10:54 AM
RE: Mill Engine Cylinder Casting - by Highpower - 08-13-2012, 03:59 PM
RE: Mill Engine Cylinder Casting - by TomG - 08-13-2012, 07:19 AM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-13-2012, 04:03 PM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-13-2012, 04:38 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-13-2012, 04:45 PM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-14-2012, 03:45 PM
RE: Mill Engine Cylinder Casting - by EdK - 08-14-2012, 04:09 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-14-2012, 04:21 PM
RE: Mill Engine Cylinder Casting - by ETC57 - 08-14-2012, 09:17 PM
RE: Mill Engine Cylinder Casting - by f350ca - 08-14-2012, 09:26 PM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-20-2012, 04:57 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-20-2012, 05:15 PM
RE: Mill Engine Cylinder Casting - by TomG - 08-20-2012, 06:11 PM
RE: Mill Engine Cylinder Casting - by Mayhem - 08-21-2012, 07:19 AM
RE: Mill Engine Cylinder Casting - by TomG - 08-21-2012, 01:15 PM
RE: Mill Engine Cylinder Casting - by dallen - 09-15-2012, 08:18 AM
RE: Mill Engine Cylinder Casting - by doubleboost - 09-15-2012, 11:17 AM
RE: Mill Engine Cylinder Casting - by DaveH - 09-15-2012, 01:04 PM
RE: Mill Engine Cylinder Casting - by dallen - 09-15-2012, 01:18 PM



Users browsing this thread: 1 Guest(s)