MetalworkingFun Forum › Machining › CNC v
4R8's table build

Thread Modes
4R8's table build
4R8
Unregistered
 
#28
11-19-2012, 05:05 PM
(11-16-2012, 05:10 PM)f350ca Wrote: Wow thats a lot of electronics and cable. Neat idea having it pull out on drawer slides.

It really was a mess before I added the black expandable sleeve.
I'm hoping the new layout in the electrical cabinet will turn out even better.

(11-16-2012, 07:01 PM)EdK Wrote: That sure is a sharp looking control center. Thumbsup

Ed

Thanks bud. You can really dress anything up with Al diamond plate! Smiley-dancenana
Reply
Thanks given by:


Messages In This Thread
4R8's table build - by 4R8 - 11-13-2012, 09:46 PM
RE: 4R8's table build - by 4R8 - 11-13-2012, 10:28 PM
RE: 4R8's table build - by f350ca - 11-13-2012, 10:31 PM
RE: 4R8's table build - by 4R8 - 11-13-2012, 11:13 PM
RE: 4R8's table build - by 4R8 - 11-14-2012, 09:40 AM
RE: 4R8's table build - by 4R8 - 11-14-2012, 10:13 AM
RE: 4R8's table build - by Mayhem - 11-14-2012, 10:14 AM
RE: 4R8's table build - by 4R8 - 11-14-2012, 10:32 AM
RE: 4R8's table build - by f350ca - 11-14-2012, 10:35 AM
RE: 4R8's table build - by 4R8 - 11-14-2012, 10:51 AM
RE: 4R8's table build - by Mayhem - 11-14-2012, 11:01 AM
RE: 4R8's table build - by 4R8 - 11-15-2012, 11:29 AM
RE: 4R8's table build - by stevec - 11-15-2012, 11:46 AM
RE: 4R8's table build - by 4R8 - 11-15-2012, 11:59 AM
RE: 4R8's table build - by 4R8 - 11-15-2012, 11:47 AM
RE: 4R8's table build - by f350ca - 11-15-2012, 01:32 PM
RE: 4R8's table build - by 4R8 - 11-15-2012, 02:21 PM
RE: 4R8's table build - by stevec - 11-15-2012, 05:54 PM
RE: 4R8's table build - by 4R8 - 11-15-2012, 11:48 PM
RE: 4R8's table build - by f350ca - 11-16-2012, 01:42 AM
RE: 4R8's table build - by 4R8 - 11-16-2012, 04:23 AM
RE: 4R8's table build - by sasquatch - 11-16-2012, 08:42 AM
RE: 4R8's table build - by 4R8 - 11-16-2012, 03:13 PM
RE: 4R8's table build - by 4R8 - 11-16-2012, 03:50 PM
RE: 4R8's table build - by 4R8 - 11-16-2012, 03:51 PM
RE: 4R8's table build - by f350ca - 11-16-2012, 05:10 PM
RE: 4R8's table build - by EdK - 11-16-2012, 07:01 PM
RE: 4R8's table build - by 4R8 - 11-19-2012, 05:05 PM
RE: 4R8's table build - by 4R8 - 11-19-2012, 05:06 PM
RE: 4R8's table build - by EdK - 11-19-2012, 05:24 PM
RE: 4R8's table build - by 4R8 - 11-21-2012, 04:11 PM



Users browsing this thread: 1 Guest(s)