Johnson Model B bandsaw
#1
Here are some pics of a Johnson Model B bandsaw I recently picked up and have started fixing up. Gonna take a while, shop time is sparse. The saw was rough, and missing a couple parts. Had to bang all the dents out of the sheet metal covers, bought a hyd cyl from ebay. Made mounts for the cylinder, bought a on/off switch, made a box for it because I couldnt find any I liked for it.
[Image: photobucket-6468-1350952829469.jpg]
[Image: photobucket-6474-1350952847860.jpg]
[Image: photobucket-5369-1350952685379.jpg]

upper cylinder mount
[Image: 2012-11-29_17-02-39_873.jpg]
mount installed
[Image: 2012-11-29_17-03-25_922.jpg]
lower mount
[Image: 2012-12-01_13-14-13_946.jpg]
with cylinder installed
[Image: 2012-11-29_17-05-08_146.jpg]
[Image: 2012-12-01_13-17-07_231.jpg]
[Image: 2012-12-01_13-17-18_237.jpg]
switch box/cord hanger I made
[Image: 2012-11-14_20-33-36_529.jpg]
installed on saw, brackets holding it on have a dog leg bent in them to get it away from the saw
[Image: 2012-11-14_20-40-59_800.jpg]
this is the auto off bracket installed
[Image: 2012-12-01_14-28-12_47.jpg]
Ill post more when/if I make any progress lol
monkers, proud to be a member of MetalworkingFun since Nov 2012.
Reply
Thanks given by:
#2
Ah, money and time, if both were plentiful it would make life so much easier.

Nice work, especially on the switch box.
Hunting American dentists since 2015.
Reply
Thanks given by:
#3
Craig,
Smiley-signs107 looking good Thumbsup
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#4
(12-02-2012, 09:38 AM)Mayhem Wrote: Nice work, especially on the switch box.

Smiley-signs064
Reply
Thanks given by:
#5
Thanks guys!! Only had a little time today to work on it, if I get a chance later I`ll post up what I did.....
monkers, proud to be a member of MetalworkingFun since Nov 2012.
Reply
Thanks given by:
#6
That will make a nice saw when it's done. Nice job on the switch adaptation!

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
#7
Thanks Monkers, did you say what the capacity of the saw is? As in ?" x ?" . I 'd like to compare it too my homemade saw.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#8
Looking good Craig, Thumbsup
I like the way the guides adjust allowing you to bring them close to the work.

Jerry.
ETC57, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
#9
Nice project!! Love that set of grey cabinets you have in the first pic background right.
sasquatch, proud to be a member of MetalworkingFun since Jul 2012.
Reply
Thanks given by:
#10
(12-02-2012, 08:07 PM)stevec Wrote: Thanks Monkers, did you say what the capacity of the saw is? As in ?" x ?" . I 'd like to compare it too my homemade saw.

Im not sure really what the capacity is, I dont have the info in front of me, maybe 5" round, 10" flat??
monkers, proud to be a member of MetalworkingFun since Nov 2012.
Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)