MetalworkingFun Forum › Machinery › Lathes v
Metal gears for 7x12s

Thread Modes
Metal gears for 7x12s
sasquatch Offline
Senior
*****
Posts: 825
Threads: 25
Joined: Jul 2012
Location: N. Bay Ontario
#19
03-17-2013, 07:14 PM
JMO, but EVERY lathe should have as Ed states one or two extra plastic gears. it would be comforting to know that if you do break it, your'e down time is going to be minimal.
sasquatch, proud to be a member of MetalworkingFun since Jul 2012.
Reply
Thanks given by:


Messages In This Thread
Metal gears for 7x12s - by Brian - 03-15-2013, 11:43 AM
RE: Metal gears for 7x12s - by EdK - 03-15-2013, 12:57 PM
RE: Metal gears for 7x12s - by stevec - 03-15-2013, 03:09 PM
RE: Metal gears for 7x12s - by sasquatch - 03-15-2013, 06:51 PM
RE: Metal gears for 7x12s - by stevec - 03-15-2013, 07:16 PM
RE: Metal gears for 7x12s - by EdK - 03-15-2013, 07:48 PM
RE: Metal gears for 7x12s - by EdK - 03-15-2013, 07:00 PM
RE: Metal gears for 7x12s - by dallen - 03-15-2013, 10:03 PM
RE: Metal gears for 7x12s - by sasquatch - 03-16-2013, 07:56 PM
RE: Metal gears for 7x12s - by Brian - 03-17-2013, 03:39 AM
RE: Metal gears for 7x12s - by Brian - 03-17-2013, 03:59 AM
RE: Metal gears for 7x12s - by Sunset Machine - 03-17-2013, 09:57 AM
RE: Metal gears for 7x12s - by stevec - 03-17-2013, 06:52 AM
RE: Metal gears for 7x12s - by EdK - 03-17-2013, 10:28 AM
RE: Metal gears for 7x12s - by EdK - 03-17-2013, 10:27 AM
RE: Metal gears for 7x12s - by stevec - 03-17-2013, 01:59 PM
RE: Metal gears for 7x12s - by Brian - 03-17-2013, 04:13 PM
RE: Metal gears for 7x12s - by stevec - 03-17-2013, 06:30 PM
RE: Metal gears for 7x12s - by Brian - 03-18-2013, 09:12 AM
RE: Metal gears for 7x12s - by sasquatch - 03-17-2013, 07:14 PM
RE: Metal gears for 7x12s - by stevec - 03-18-2013, 03:58 PM
RE: Metal gears for 7x12s - by Brian - 03-26-2013, 03:51 AM
RE: Metal gears for 7x12s - by Brian - 04-07-2013, 03:04 AM
RE: Metal gears for 7x12s - by EdK - 04-07-2013, 09:07 AM
RE: Metal gears for 7x12s - by Brian - 04-07-2013, 01:24 PM
RE: Metal gears for 7x12s - by Dave J - 04-07-2013, 08:20 AM
RE: Metal gears for 7x12s - by Brian - 04-17-2013, 04:43 PM



Users browsing this thread: 2 Guest(s)