Cutting Speed and RPM on the Lathe and Mill

Hello There, Guest! Register

Thread Modes

Cutting Speed and RPM on the Lathe and Mill

Hawkeye Offline

Offline

Junior

Posts: 532
Threads: 39
Joined: Jan 2013
Location: Kelowna, BC, Canada

#31

10-04-2013, 09:53 AM

When I installed a VFD and MachTach on my ZX-25 mill and Hercus lathe, my finish quality went way up and tool breakage went way down. I had been using my cutting speed charts, but sometimes went with 'close enough' if faced with a slight belt change.

I have three MachTachs running on four machines. Nice work, Henry.

Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Cutting Speed and RPM on the Lathe and Mill - by TomG - 09-30-2013, 11:30 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by b4dyc - 10-01-2013, 05:46 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-01-2013, 07:11 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 08:01 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-01-2013, 08:19 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by b4dyc - 10-01-2013, 08:41 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by PixMan - 10-01-2013, 08:57 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-01-2013, 08:58 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by dallen - 10-01-2013, 09:23 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 10:26 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by stevec - 10-01-2013, 01:03 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by chucketn - 10-01-2013, 11:33 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 01:15 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-01-2013, 08:31 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 08:40 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by f350ca - 10-01-2013, 10:49 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-01-2013, 11:11 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-02-2013, 06:20 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-02-2013, 07:16 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-02-2013, 09:37 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by arvidj - 10-02-2013, 09:20 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-02-2013, 10:25 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-03-2013, 10:17 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-03-2013, 11:35 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Micktoon - 10-03-2013, 05:07 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by Micktoon - 10-04-2013, 04:09 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-04-2013, 08:23 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-03-2013, 07:42 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by henryarnold - 10-03-2013, 11:16 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-04-2013, 05:35 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Highpower - 10-04-2013, 09:41 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Mayhem - 10-04-2013, 07:16 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-04-2013, 04:05 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-04-2013, 07:13 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by Hawkeye - 10-04-2013, 09:53 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by LJP - 10-04-2013, 11:29 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-04-2013, 07:10 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by EdK - 10-05-2013, 09:02 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-05-2013, 10:15 AM

RE: Cutting Speed and RPM on the Lathe and Mill - by Micktoon - 10-05-2013, 06:24 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by krv3000 - 10-06-2013, 01:57 PM

RE: Cutting Speed and RPM on the Lathe and Mill - by TomG - 10-06-2013, 05:49 PM

Users browsing this thread: 1 Guest(s)