drip oilers
#9
(11-09-2013, 09:55 AM)EdK Wrote: Nice job on the form tool David. Thumbsup

Ed

it should of been flat on top with no rake, but the bit was one that I had already used for something else and the side I turned up only had a slight negitive rake on it. It actually cut pretty good, I had it on center and would crank the cross slide in about 10 15 thousands and then run the carriage into the part to the depth that I needed, using lots of dark cutting oil.


(11-09-2013, 10:51 AM)DaveH Wrote: Coming a long nicely Thumbsup
Smiley-eatdrink004
DaveH

Dave, I've reached the point of needing the glass tube's, or I may just use some stainless steel tubing I have so I can call them done till I get the glass. They have actually been a lot easier to make then I had first thought they would be.

The one part that I haven't really figured out is the little cover over the filler hole as its spring loaded I may just put in a tube with a drop cap on it and a little chain or something to keep them from getting misplaced.
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:


Messages In This Thread
drip oilers - by dallen - 10-31-2013, 11:08 PM
RE: drip oilers - by sasquatch - 11-01-2013, 05:14 PM
RE: drip oilers - by dallen - 11-01-2013, 08:47 PM
RE: drip oilers - by dallen - 11-02-2013, 10:47 AM
RE: drip oilers - by dallen - 11-05-2013, 12:08 PM
RE: drip oilers - by dallen - 11-08-2013, 10:12 PM
RE: drip oilers - by EdK - 11-09-2013, 09:55 AM
RE: drip oilers - by DaveH - 11-09-2013, 10:51 AM
RE: drip oilers - by dallen - 11-09-2013, 11:17 AM
RE: drip oilers - by cast iron - 12-25-2013, 06:16 PM
RE: drip oilers - by krv3000 - 11-09-2013, 04:58 PM
RE: drip oilers - by dallen - 11-10-2013, 05:57 PM
RE: drip oilers - by DaveH - 11-10-2013, 06:16 PM
RE: drip oilers - by dallen - 11-10-2013, 06:34 PM
RE: drip oilers - by Mayhem - 11-11-2013, 08:18 AM
RE: drip oilers - by dallen - 11-11-2013, 08:40 AM
RE: drip oilers - by Mayhem - 11-11-2013, 08:42 AM
RE: drip oilers - by dallen - 11-11-2013, 08:46 AM
RE: drip oilers - by dallen - 11-13-2013, 04:46 PM
RE: drip oilers - by ScrapMetal - 11-13-2013, 05:39 PM
RE: drip oilers - by dallen - 12-04-2013, 09:10 PM
RE: drip oilers - by stevec - 12-05-2013, 06:50 AM
RE: drip oilers - by dallen - 12-05-2013, 09:17 AM
RE: drip oilers - by sasquatch - 12-05-2013, 05:48 PM
RE: drip oilers - by stevec - 12-05-2013, 06:47 PM
RE: drip oilers - by dallen - 12-14-2013, 05:03 PM
RE: drip oilers - by DaveH - 12-15-2013, 07:08 AM
RE: drip oilers - by dallen - 12-15-2013, 08:07 AM
RE: drip oilers - by dallen - 12-15-2013, 01:14 PM
RE: drip oilers - by EdK - 12-15-2013, 02:17 PM
RE: drip oilers - by dallen - 12-15-2013, 02:34 PM
RE: drip oilers - by DaveH - 12-15-2013, 06:57 PM
RE: drip oilers - by dallen - 12-15-2013, 08:00 PM
RE: drip oilers - by f350ca - 12-15-2013, 08:16 PM
RE: drip oilers - by big job - 12-16-2013, 05:09 AM
RE: drip oilers - by dallen - 12-16-2013, 07:49 AM
RE: drip oilers - by dallen - 12-25-2013, 07:48 PM
RE: drip oilers - by stevec - 12-26-2013, 07:56 AM
RE: drip oilers - by dallen - 12-26-2013, 10:30 AM
RE: drip oilers - by ScrapMetal - 12-26-2013, 05:22 PM
RE: drip oilers - by Scruffy - 03-25-2014, 12:39 PM
RE: drip oilers - by EdK - 03-25-2014, 03:38 PM



Users browsing this thread: 2 Guest(s)