12-11-2013, 11:42 AM
Here's my Phase II version that came with my QCTP set. I've never used it. Very crudely made and without the side taper so it would only be good for flat blades.
Ed
Ed
|
Parting on the Lathe
|
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
Parting on the Lathe - by TomG - 12-07-2013, 09:16 PM
RE: Parting on the Lathe - by PixMan - 12-08-2013, 12:04 AM
RE: Parting on the Lathe - by TomG - 12-08-2013, 12:19 AM
RE: Parting on the Lathe - by Shawn - 12-08-2013, 04:08 AM
RE: Parting on the Lathe - by TomG - 12-08-2013, 10:03 AM
RE: Parting on the Lathe - by PixMan - 12-08-2013, 08:27 AM
RE: Parting on the Lathe - by EdK - 12-08-2013, 10:08 AM
RE: Parting on the Lathe - by TomG - 12-09-2013, 09:05 AM
RE: Parting on the Lathe - by EdK - 12-09-2013, 01:10 PM
RE: Parting on the Lathe - by f350ca - 12-08-2013, 10:09 AM
RE: Parting on the Lathe - by TomG - 12-08-2013, 10:09 AM
RE: Parting on the Lathe - by Micktoon - 12-08-2013, 06:16 PM
RE: Parting on the Lathe - by TomG - 12-08-2013, 06:39 PM
RE: Parting on the Lathe - by Hawkeye - 12-08-2013, 11:09 PM
RE: Parting on the Lathe - by TomG - 12-09-2013, 12:07 AM
RE: Parting on the Lathe - by awemawson - 12-09-2013, 04:13 AM
RE: Parting on the Lathe - by TomG - 12-09-2013, 09:09 AM
RE: Parting on the Lathe - by Micktoon - 12-09-2013, 08:27 AM
RE: Parting on the Lathe - by awemawson - 12-09-2013, 10:14 AM
RE: Parting on the Lathe - by TomG - 12-09-2013, 11:32 AM
RE: Parting on the Lathe - by awemawson - 12-09-2013, 12:41 PM
RE: Parting on the Lathe - by PixMan - 12-09-2013, 01:31 PM
RE: Parting on the Lathe - by awemawson - 12-09-2013, 01:41 PM
RE: Parting on the Lathe - by f350ca - 12-09-2013, 01:33 PM
RE: Parting on the Lathe - by paulmo101 - 12-09-2013, 03:02 PM
RE: Parting on the Lathe - by EdK - 12-09-2013, 04:26 PM
RE: Parting on the Lathe - by TomG - 12-09-2013, 05:41 PM
RE: Parting on the Lathe - by EdK - 12-09-2013, 06:18 PM
RE: Parting on the Lathe - by TomG - 12-09-2013, 08:44 PM
RE: Parting on the Lathe - by EdK - 12-10-2013, 06:31 AM
RE: Parting on the Lathe - by PixMan - 12-09-2013, 06:59 PM
RE: Parting on the Lathe - by PixMan - 12-09-2013, 10:03 PM
RE: Parting on the Lathe - by dallen - 12-10-2013, 10:41 AM
RE: Parting on the Lathe - by TomG - 12-10-2013, 10:57 AM
RE: Parting on the Lathe - by dallen - 12-10-2013, 12:30 PM
RE: Parting on the Lathe - by awemawson - 12-10-2013, 12:49 PM
RE: Parting on the Lathe - by PixMan - 12-11-2013, 08:48 AM
RE: Parting on the Lathe - by Mayhem - 12-11-2013, 09:34 AM
RE: Parting on the Lathe - by dallen - 12-11-2013, 09:57 AM
RE: Parting on the Lathe - by TomG - 12-11-2013, 11:20 AM
RE: Parting on the Lathe - by dallen - 12-11-2013, 05:53 PM
RE: Parting on the Lathe - by stevec - 12-11-2013, 11:38 AM
RE: Parting on the Lathe - by TomG - 12-11-2013, 12:24 PM
RE: Parting on the Lathe - by ScrapMetal - 12-11-2013, 05:31 PM
RE: Parting on the Lathe - by EdK - 12-11-2013, 11:42 AM
RE: Parting on the Lathe - by 7mag - 12-18-2013, 09:28 AM
RE: Parting on the Lathe - by TomG - 12-18-2013, 10:07 AM
RE: Parting on the Lathe - by stevec - 07-22-2014, 05:46 PM
RE: Parting on the Lathe - by EdK - 07-22-2014, 06:22 PM
RE: Parting on the Lathe - by stevec - 07-22-2014, 07:48 PM
|
Users browsing this thread: 2 Guest(s)