Parting on the Lathe

Hello There, Guest! Register

Thread Modes

Parting on the Lathe

TomG Offline

Offline

Alt. Whipping Boy

Posts: 3,795
Threads: 183
Joined: Jun 2012
Location: Farmington Hills, Michigan

#43

12-11-2013, 12:24 PM

(12-11-2013, 11:38 AM)stevec Wrote: Tom, someday I'm gonna make a BXA size parting blade holder like that but not with the slant that requires one to adjust the height each time the blade is extended or retracted.

Steve,

I've never understood that angle. It's not like a couple of degrees of back rake is going to significantly change the way the tool performs, but it sure is a pain when adjusting the extension and center height.

Tom

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Parting on the Lathe - by TomG - 12-07-2013, 09:16 PM

RE: Parting on the Lathe - by PixMan - 12-08-2013, 12:04 AM

RE: Parting on the Lathe - by TomG - 12-08-2013, 12:19 AM

RE: Parting on the Lathe - by Shawn - 12-08-2013, 04:08 AM

RE: Parting on the Lathe - by TomG - 12-08-2013, 10:03 AM

RE: Parting on the Lathe - by PixMan - 12-08-2013, 08:27 AM

RE: Parting on the Lathe - by EdK - 12-08-2013, 10:08 AM

RE: Parting on the Lathe - by TomG - 12-09-2013, 09:05 AM

RE: Parting on the Lathe - by EdK - 12-09-2013, 01:10 PM

RE: Parting on the Lathe - by f350ca - 12-08-2013, 10:09 AM

RE: Parting on the Lathe - by TomG - 12-08-2013, 10:09 AM

RE: Parting on the Lathe - by Micktoon - 12-08-2013, 06:16 PM

RE: Parting on the Lathe - by TomG - 12-08-2013, 06:39 PM

RE: Parting on the Lathe - by Hawkeye - 12-08-2013, 11:09 PM

RE: Parting on the Lathe - by TomG - 12-09-2013, 12:07 AM

RE: Parting on the Lathe - by awemawson - 12-09-2013, 04:13 AM

RE: Parting on the Lathe - by TomG - 12-09-2013, 09:09 AM

RE: Parting on the Lathe - by Micktoon - 12-09-2013, 08:27 AM

RE: Parting on the Lathe - by awemawson - 12-09-2013, 10:14 AM

RE: Parting on the Lathe - by TomG - 12-09-2013, 11:32 AM

RE: Parting on the Lathe - by awemawson - 12-09-2013, 12:41 PM

RE: Parting on the Lathe - by PixMan - 12-09-2013, 01:31 PM

RE: Parting on the Lathe - by awemawson - 12-09-2013, 01:41 PM

RE: Parting on the Lathe - by f350ca - 12-09-2013, 01:33 PM

RE: Parting on the Lathe - by paulmo101 - 12-09-2013, 03:02 PM

RE: Parting on the Lathe - by EdK - 12-09-2013, 04:26 PM

RE: Parting on the Lathe - by TomG - 12-09-2013, 05:41 PM

RE: Parting on the Lathe - by EdK - 12-09-2013, 06:18 PM

RE: Parting on the Lathe - by TomG - 12-09-2013, 08:44 PM

RE: Parting on the Lathe - by EdK - 12-10-2013, 06:31 AM

RE: Parting on the Lathe - by PixMan - 12-09-2013, 06:59 PM

RE: Parting on the Lathe - by PixMan - 12-09-2013, 10:03 PM

RE: Parting on the Lathe - by dallen - 12-10-2013, 10:41 AM

RE: Parting on the Lathe - by TomG - 12-10-2013, 10:57 AM

RE: Parting on the Lathe - by dallen - 12-10-2013, 12:30 PM

RE: Parting on the Lathe - by awemawson - 12-10-2013, 12:49 PM

RE: Parting on the Lathe - by PixMan - 12-11-2013, 08:48 AM

RE: Parting on the Lathe - by Mayhem - 12-11-2013, 09:34 AM

RE: Parting on the Lathe - by dallen - 12-11-2013, 09:57 AM

RE: Parting on the Lathe - by TomG - 12-11-2013, 11:20 AM

RE: Parting on the Lathe - by dallen - 12-11-2013, 05:53 PM

RE: Parting on the Lathe - by stevec - 12-11-2013, 11:38 AM

RE: Parting on the Lathe - by TomG - 12-11-2013, 12:24 PM

RE: Parting on the Lathe - by ScrapMetal - 12-11-2013, 05:31 PM

RE: Parting on the Lathe - by EdK - 12-11-2013, 11:42 AM

RE: Parting on the Lathe - by 7mag - 12-18-2013, 09:28 AM

RE: Parting on the Lathe - by TomG - 12-18-2013, 10:07 AM

RE: Parting on the Lathe - by stevec - 07-22-2014, 05:46 PM

RE: Parting on the Lathe - by EdK - 07-22-2014, 06:22 PM

RE: Parting on the Lathe - by stevec - 07-22-2014, 07:48 PM

Users browsing this thread: 2 Guest(s)