Clamp Type Knurling Tool
#6
(11-20-2014, 10:53 AM)Dr Stan Wrote: Tom,

Very nice design & drawings.   Thumbsup   I especially like removing the stress from the cross slide.

What is the largest diameter it is designed to knurl?

One comment/suggestion.  I'd add the 10-32 bolt hole pattern on the back/bottom of the holder which would enable one to mount it 90 degrees from the existing design.  I think it would give the knurler more options for mounting and probably reduce tailstock extension making the set-up more rigid.  That would be especially advantageous to those with smaller (< 10") lathes.

Thanks,

Stan

Thanks Stan.

The largest diameter that can be knurled is 2".

I'm not sure what you mean by adding a bolt hole pattern to the bottom. Also what do you mean by "tailstock extension"? The tool is meant to mount in a quick change tool post.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:


Messages In This Thread
Clamp Type Knurling Tool - by TomG - 11-16-2014, 08:53 PM
RE: Clamp Type Knurling Tool - by schor - 11-16-2014, 09:43 PM
RE: Clamp Type Knurling Tool - by dallen - 11-16-2014, 10:01 PM
RE: Clamp Type Knurling Tool - by Dr Stan - 11-20-2014, 10:53 AM
RE: Clamp Type Knurling Tool - by TomG - 11-20-2014, 11:51 AM
RE: Clamp Type Knurling Tool - by Dr Stan - 11-20-2014, 11:14 PM
RE: Clamp Type Knurling Tool - by PixMan - 11-20-2014, 11:07 AM
RE: Clamp Type Knurling Tool - by TomG - 11-20-2014, 11:58 AM
RE: Clamp Type Knurling Tool - by RobWilson - 11-20-2014, 12:24 PM
RE: Clamp Type Knurling Tool - by TomG - 11-20-2014, 01:09 PM
RE: Clamp Type Knurling Tool - by RobWilson - 11-20-2014, 01:14 PM
RE: Clamp Type Knurling Tool - by PixMan - 11-20-2014, 02:31 PM
RE: Clamp Type Knurling Tool - by TomG - 11-20-2014, 08:29 PM
RE: Clamp Type Knurling Tool - by Mayhem - 11-20-2014, 07:58 PM
RE: Clamp Type Knurling Tool - by PixMan - 11-20-2014, 08:16 PM
RE: Clamp Type Knurling Tool - by Dr Stan - 11-20-2014, 11:22 PM
RE: Clamp Type Knurling Tool - by TomG - 11-20-2014, 08:30 PM
RE: Clamp Type Knurling Tool - by PixMan - 11-20-2014, 11:56 PM
RE: Clamp Type Knurling Tool - by TomG - 11-21-2014, 12:28 AM
RE: Clamp Type Knurling Tool - by dallen - 11-21-2014, 12:42 AM
RE: Clamp Type Knurling Tool - by ironman - 11-25-2014, 02:31 AM
RE: Clamp Type Knurling Tool - by TomG - 11-25-2014, 10:35 AM
RE: Clamp Type Knurling Tool - by DaveH - 11-25-2014, 03:00 PM
RE: Clamp Type Knurling Tool - by ironman - 11-27-2014, 02:52 AM
RE: Clamp Type Knurling Tool - by TomG - 11-25-2014, 03:47 PM
RE: Clamp Type Knurling Tool - by JScott - 11-25-2014, 04:52 PM
RE: Clamp Type Knurling Tool - by TomG - 11-25-2014, 05:20 PM
RE: Clamp Type Knurling Tool - by EdK - 11-25-2014, 05:24 PM
RE: Clamp Type Knurling Tool - by DaveH - 11-25-2014, 06:29 PM
RE: Clamp Type Knurling Tool - by stevec - 11-25-2014, 06:33 PM
RE: Clamp Type Knurling Tool - by TomG - 11-27-2014, 09:46 AM
RE: Clamp Type Knurling Tool - by TomG - 11-30-2014, 01:25 AM
RE: Clamp Type Knurling Tool - by Mayhem - 11-30-2014, 02:57 AM
RE: Clamp Type Knurling Tool - by big job - 11-30-2014, 04:58 AM
RE: Clamp Type Knurling Tool - by Arbalest - 11-30-2014, 05:34 AM
RE: Clamp Type Knurling Tool - by TomG - 11-30-2014, 09:36 AM
RE: Clamp Type Knurling Tool - by EdK - 11-30-2014, 12:21 PM
RE: Clamp Type Knurling Tool - by Arbalest - 11-30-2014, 02:06 PM
RE: Clamp Type Knurling Tool - by EdK - 11-30-2014, 02:15 PM
RE: Clamp Type Knurling Tool - by dallen - 11-30-2014, 02:27 PM
RE: Clamp Type Knurling Tool - by EdK - 11-30-2014, 03:10 PM
RE: Clamp Type Knurling Tool - by Arbalest - 11-30-2014, 02:53 PM
RE: Clamp Type Knurling Tool - by EdK - 12-04-2014, 07:08 PM
RE: Clamp Type Knurling Tool - by TomG - 12-04-2014, 07:34 PM



Users browsing this thread: 1 Guest(s)