MetalworkingFun Forum › Machining › General Metalworking Discussion v
help with angle iron's

Thread Modes
help with angle iron's
f350ca Offline
Senior
*****
Posts: 3,002
Threads: 51
Joined: Apr 2012
Location: Ontario
#6
01-10-2015, 10:00 PM
As Ed said buffing the aluminium will bring out the bling, first sanding it with say 320 grit on an orbital sander will speed up the process and smooth out the marks let from the extruder.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:


Messages In This Thread
help with angle iron's - by dbreeze225 - 01-10-2015, 06:55 PM
RE: help with angle iron's - by PixMan - 01-10-2015, 07:33 PM
RE: help with angle iron's - by dbreeze225 - 01-10-2015, 08:06 PM
RE: help with angle iron's - by EdK - 01-10-2015, 08:22 PM
RE: help with angle iron's - by Highpower - 01-10-2015, 09:39 PM
RE: help with angle iron's - by f350ca - 01-10-2015, 10:00 PM
RE: help with angle iron's - by PixMan - 01-10-2015, 10:52 PM
RE: help with angle iron's - by trevatxtal - 01-11-2015, 08:29 AM
RE: help with angle iron's - by dbreeze225 - 01-11-2015, 11:33 AM
RE: help with angle iron's - by EdK - 01-11-2015, 11:59 AM
RE: help with angle iron's - by dbreeze225 - 01-11-2015, 12:10 PM
RE: help with angle iron's - by EdK - 01-11-2015, 12:19 PM
RE: help with angle iron's - by Dr Stan - 01-12-2015, 11:48 AM
RE: help with angle iron's - by dbreeze225 - 01-12-2015, 12:31 PM
RE: help with angle iron's - by stevec - 01-13-2015, 08:05 AM
RE: help with angle iron's - by Mayhem - 01-13-2015, 08:49 AM
RE: help with angle iron's - by EdK - 01-13-2015, 09:54 AM
RE: help with angle iron's - by dbreeze225 - 01-13-2015, 12:19 PM
RE: help with angle iron's - by EdK - 01-13-2015, 12:42 PM
RE: help with angle iron's - by dbreeze225 - 01-13-2015, 01:00 PM
RE: help with angle iron's - by DaveH - 01-13-2015, 01:58 PM
RE: help with angle iron's - by DaveH - 01-13-2015, 02:16 PM
RE: help with angle iron's - by dbreeze225 - 01-13-2015, 04:53 PM
RE: help with angle iron's - by EdK - 01-13-2015, 05:41 PM
RE: help with angle iron's - by DaveH - 01-13-2015, 06:10 PM
RE: help with angle iron's - by dbreeze225 - 01-13-2015, 08:17 PM
RE: help with angle iron's - by DaveH - 01-13-2015, 08:58 PM
RE: help with angle iron's - by dbreeze225 - 01-14-2015, 01:18 PM
RE: help with angle iron's - by DaveH - 01-14-2015, 01:39 PM
RE: help with angle iron's - by dbreeze225 - 01-14-2015, 02:20 PM
RE: help with angle iron's - by EdK - 01-14-2015, 05:00 PM
RE: help with angle iron's - by f350ca - 01-14-2015, 05:54 PM
RE: help with angle iron's - by Dr Stan - 01-14-2015, 07:19 PM
RE: help with angle iron's - by dbreeze225 - 01-15-2015, 12:27 PM
RE: help with angle iron's - by DaveH - 01-15-2015, 01:06 PM
RE: help with angle iron's - by DaveH - 01-15-2015, 01:11 PM
RE: help with angle iron's - by Highpower - 01-15-2015, 02:50 PM
RE: help with angle iron's - by DaveH - 01-15-2015, 03:07 PM
RE: help with angle iron's - by EdK - 01-15-2015, 06:12 PM
RE: help with angle iron's - by stevec - 01-15-2015, 06:33 PM
RE: help with angle iron's - by EdK - 01-15-2015, 06:36 PM
RE: help with angle iron's - by DaveH - 01-15-2015, 06:58 PM
RE: help with angle iron's - by dbreeze225 - 01-16-2015, 06:40 PM
RE: help with angle iron's - by EdK - 01-16-2015, 06:55 PM
RE: help with angle iron's - by DaveH - 01-16-2015, 06:56 PM
RE: help with angle iron's - by dbreeze225 - 01-16-2015, 07:12 PM
RE: help with angle iron's - by dbreeze225 - 01-16-2015, 07:20 PM
RE: help with angle iron's - by DaveH - 01-16-2015, 07:23 PM
RE: help with angle iron's - by EdK - 01-16-2015, 07:29 PM
RE: help with angle iron's - by f350ca - 01-16-2015, 08:59 PM
RE: help with angle iron's - by EdK - 01-16-2015, 09:12 PM
RE: help with angle iron's - by dbreeze225 - 01-17-2015, 01:11 PM
RE: help with angle iron's - by DaveH - 01-17-2015, 01:35 PM
RE: help with angle iron's - by dbreeze225 - 01-17-2015, 01:41 PM
RE: help with angle iron's - by EdK - 01-17-2015, 02:05 PM
RE: help with angle iron's - by dbreeze225 - 01-17-2015, 04:25 PM
RE: help with angle iron's - by DaveH - 01-23-2015, 07:12 PM
RE: help with angle iron's - by rleete - 01-23-2015, 08:20 PM



Users browsing this thread: 1 Guest(s)