MetalworkingFun Forum › Machining › General Metalworking Discussion v
What face mill do u use???

Thread Modes
What face mill do u use???
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#23
03-09-2015, 12:42 PM
This one 'Walter F4041'.     it can be used for just facing though, because Ken suggested it. Big Grin  and you did use it for facing with one insert.

May be it should be called 'shoulder/face' mill Thumbsup

I think this is where Ken was talking about damaging the empty pockets if it is used as a shoulder cutter, can easily happen.

Anyway it doesn't matter what it is called  " a rose by any other name" Big Grin

Smiley-eatdrink004
DaveH
Reply
Thanks given by: aRM


Messages In This Thread
What face mill do u use??? - by aRM - 03-08-2015, 04:03 PM
RE: WHAT FACEMILL DO U USE ??? - by EdK - 03-08-2015, 04:18 PM
RE: WHAT FACEMILL DO U USE ??? - by aRM - 03-08-2015, 04:45 PM
RE: WHAT FACEMILL DO U USE ??? - by stevec - 03-08-2015, 05:20 PM
RE: WHAT FACEMILL DO U USE ??? - by PixMan - 03-08-2015, 06:26 PM
RE: What face mill do u use??? - by stevec - 03-08-2015, 06:51 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 06:59 PM
RE: What face mill do u use??? - by stevec - 03-08-2015, 07:11 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 07:21 PM
RE: What face mill do u use??? - by mike-sid - 03-08-2015, 08:21 PM
RE: What face mill do u use??? - by Highpower - 03-08-2015, 08:32 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 09:52 PM
RE: What face mill do u use??? - by mike-sid - 03-08-2015, 10:21 PM
RE: What face mill do u use??? - by Highpower - 03-08-2015, 11:47 PM
RE: What face mill do u use??? - by PixMan - 03-08-2015, 10:32 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 06:46 AM
RE: What face mill do u use??? - by Highpower - 03-09-2015, 10:06 AM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 11:31 AM
RE: What face mill do u use??? - by EdK - 03-09-2015, 12:02 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:19 PM
RE: What face mill do u use??? - by EdK - 03-09-2015, 12:26 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 12:40 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:42 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 12:48 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:56 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 12:52 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 01:36 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 01:53 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 02:32 PM
RE: What face mill do u use??? - by DaveH - 03-09-2015, 01:56 PM
RE: What face mill do u use??? - by aRM - 03-09-2015, 02:53 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 10:55 PM
RE: What face mill do u use??? - by aRM - 03-10-2015, 12:30 AM
RE: What face mill do u use??? - by aRM - 03-13-2015, 02:33 PM
RE: What face mill do u use??? - by PixMan - 03-09-2015, 06:07 PM
RE: What face mill do u use??? - by aRM - 03-10-2015, 12:05 AM
RE: What face mill do u use??? - by Mayhem - 03-10-2015, 05:44 AM
RE: What face mill do u use??? - by PixMan - 03-10-2015, 07:45 AM
RE: What face mill do u use??? - by aRM - 03-11-2015, 12:47 PM
RE: What face mill do u use??? - by PixMan - 03-11-2015, 04:22 PM
RE: What face mill do u use??? - by aRM - 03-13-2015, 03:24 PM
RE: What face mill do u use??? - by PixMan - 03-11-2015, 09:27 PM
RE: What face mill do u use??? - by DaveH - 03-13-2015, 03:50 PM
RE: What face mill do u use??? - by PixMan - 03-13-2015, 07:22 PM
RE: What face mill do u use??? - by aRM - 03-18-2015, 02:59 PM
RE: What face mill do u use??? - by DaveH - 03-18-2015, 03:16 PM
RE: What face mill do u use??? - by aRM - 03-19-2015, 01:31 PM
RE: What face mill do u use??? - by DaveH - 03-18-2015, 03:49 PM
RE: What face mill do u use??? - by aRM - 03-19-2015, 01:43 PM
RE: What face mill do u use??? - by Vinny - 03-18-2015, 04:45 PM
RE: What face mill do u use??? - by DaveH - 03-18-2015, 05:15 PM
RE: What face mill do u use??? - by PixMan - 03-18-2015, 05:41 PM
RE: What face mill do u use??? - by aRM - 03-19-2015, 02:01 PM
RE: What face mill do u use??? - by DaveH - 03-19-2015, 03:24 PM
RE: What face mill do u use??? - by aRM - 03-20-2015, 02:19 PM
RE: What face mill do u use??? - by PixMan - 03-19-2015, 07:02 PM
RE: What face mill do u use??? - by aRM - 03-20-2015, 02:33 PM
RE: What face mill do u use??? - by DaveH - 03-20-2015, 02:56 PM
RE: What face mill do u use??? - by aRM - 03-22-2015, 12:00 PM
RE: What face mill do u use??? - by PixMan - 03-20-2015, 04:28 PM
RE: What face mill do u use??? - by aRM - 03-22-2015, 12:31 PM
RE: What face mill do u use??? - by DaveH - 03-22-2015, 01:36 PM
RE: What face mill do u use??? - by aRM - 03-24-2015, 12:12 AM
RE: What face mill do u use??? - by Mayhem - 03-24-2015, 05:49 AM
RE: What face mill do u use??? - by aRM - 03-24-2015, 01:49 PM
RE: What face mill do u use??? - by PixMan - 03-22-2015, 01:46 PM
RE: What face mill do u use??? - by aRM - 03-24-2015, 02:28 PM
RE: What face mill do u use??? - by PixMan - 03-22-2015, 02:08 PM
RE: What face mill do u use??? - by aRM - 03-24-2015, 12:21 AM
RE: What face mill do u use??? - by PixMan - 03-24-2015, 10:38 PM
RE: What face mill do u use??? - by aRM - 03-25-2015, 12:07 AM



Users browsing this thread: 1 Guest(s)