5 Cylinder Radial
I have had a few queries regarding the corrected link pin positions on the master rod, so I made 2 dummy pistons, one for the master rod  and another for the cylinder under test, 
A protractor was stuck with double sided tape to the back of the casing and a pointer attached to the crank shaft and zeroed at No1TDC
the other cylinders where then tested and came up to TDC at the correct intervals, so I am content .
Brian.  Smiley-dancenana

   
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
At last the oil pump is beginning to take shape.
Being restricted to house, only going out when absolutely necessary has it's advantages.

Brian.


Attached Files Thumbnail(s)
   
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
New toy arrived  yesterday I understand these a useful for trimming fingernails.

   

Brian. Smiley-dancenana
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
What's that? About 26, 28 inches? Impressive.
Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.
Reply
Thanks given by:
Hi Mike
It's a 24x10 Just to get it running!! I had to get a prop now so I can make the flange, all the adverts don't give hub diameter or depth
just bore size.
Brian
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
Mounting the propeller gave me more  problems, one being how to make a nice contour on the spinner. so I decided to make a attachment for the lathe, I have studs in the chip tray to mount my taper turning attachment , so I attached a piece of angle in line with the bed and turned a master disk the same radius as the profile of the spinner.
The feed screw was removed from the cross slide and a stylus fitted to it's rear end.
The compound slide was turned to provide the feed.
   

The cut was taken outwards from the chuck using the powered lead screw, and hand pressure was used to keep the stylus in contact with the master.
   

I am very pleased with the result and I have a new piece of kit as a bonus.
   
   

Brian.
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
Nice job Brian. Thumbsup

Tru-Trace made a 3D hydraulic version for Bridgeports, but I've never seen one on a lathe.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
That's it job done.

   

   Brian.    Smiley-dancenana
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
(04-28-2020, 08:31 AM)TomG Wrote: Nice job Brian. Thumbsup

Tru-Trace made a 3D hydraulic version for Bridgeports, but I've never seen one on a lathe.

Tom

I've even seen one on a VTL.
Reply
Thanks given by:
(04-28-2020, 09:20 AM)Brian Wrote: That's it job done.
   Brian.    Smiley-dancenana

Job done? As in the engine is completed? Fantastic Brian, it has been an inspiration to watch this take shape. 5 years since the first post in this thread.
PLEASE post a video of it running.
Lathe (n); a machine tool used in the production of milling machine components.

Milling Machine (n); a machine tool used in the production of lathe components.
Reply
Thanks given by:




Users browsing this thread: 3 Guest(s)