ER32 Collet Chuck for Proxxon PD 400
#61
A little update.

Found a suitable aluminium stock to make the gauge for the recess.

[Image: 8ee830fd.jpg]

After turning steel, I forgotten how easy it is to turn aluminium. A little was turn off the diameter till it just fit the recess at the back of the 4 jaw chuck.

[Image: 61e03f10.jpg]

[Image: 1f046355.jpg]

[Image: 0c60d483.jpg]

[Image: 215b74d8.jpg]

The partially completed chuck remounted in the 3 jaw to turn off the OD and square off the back.

[Image: 7bbc87ee.jpg]

[Image: 80fb691c.jpg]

Finally, I'm ready to turn the recess.

[Image: 3c0556d1.jpg]

But that will be in the next session either tonight or tomorrow morning.
Wongster
http://www.wongstersproduction.com

Proud to be a member of MetalworkingFun Forum since Mar 2012.
Reply
Thanks given by:


Messages In This Thread
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 04-15-2012, 06:35 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 04-16-2012, 09:29 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 04-16-2012, 10:13 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 04-16-2012, 11:11 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 04-16-2012, 12:36 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 05-01-2012, 09:06 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 05-01-2012, 11:23 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 05-01-2012, 12:22 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 05-07-2012, 06:20 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by Wongster - 05-19-2012, 02:40 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 05-19-2012, 04:23 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 05-20-2012, 04:37 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 05-20-2012, 01:07 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 05-20-2012, 01:23 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 05-20-2012, 01:40 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 05-20-2012, 03:25 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 05-31-2012, 04:26 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by RobWilson - 06-01-2012, 02:40 AM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 06-20-2012, 08:06 PM
RE: ER32 Collet Chuck for Proxxon PD 400 - by EdK - 06-25-2012, 03:14 PM



Users browsing this thread: 5 Guest(s)