home made mill
#34
hi all thanks for the comments I was in work today so I finish off the extension set it up in the 4 jaw chuck then clocked it in then took it dawn to length then turned the spigot then made the groove for the clamping brackets     will post more pics tomorrow of it going together im thinking of splitting the extension to boar out the centre to make it lighter any way pics


Attached Files Thumbnail(s)
                           
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:


Messages In This Thread
home made mill - by krv3000 - 06-19-2016, 03:58 PM
RE: home made mill - by Micktoon - 06-19-2016, 05:46 PM
RE: home made mill - by krv3000 - 06-20-2016, 05:15 PM
RE: home made mill - by krv3000 - 07-02-2016, 02:52 PM
RE: home made mill - by krv3000 - 07-02-2016, 02:57 PM
RE: home made mill - by Micktoon - 07-02-2016, 06:10 PM
RE: home made mill - by Mayhem - 07-02-2016, 07:31 PM
RE: home made mill - by krv3000 - 07-03-2016, 12:18 PM
RE: home made mill - by pepi - 07-04-2016, 06:07 AM
RE: home made mill - by krv3000 - 07-04-2016, 01:34 PM
RE: home made mill - by krv3000 - 07-08-2016, 04:37 PM
RE: home made mill - by rleete - 07-08-2016, 06:50 PM
RE: home made mill - by Mayhem - 07-08-2016, 08:24 PM
RE: home made mill - by krv3000 - 07-10-2016, 03:07 PM
RE: home made mill - by pepi - 07-10-2016, 10:05 PM
RE: home made mill - by krv3000 - 07-11-2016, 02:00 PM
RE: home made mill - by Micktoon - 07-11-2016, 06:25 PM
RE: home made mill - by krv3000 - 07-12-2016, 04:45 PM
RE: home made mill - by krv3000 - 07-25-2016, 04:11 PM
RE: home made mill - by EdK - 07-25-2016, 04:12 PM
RE: home made mill - by krv3000 - 08-01-2016, 01:13 PM
RE: home made mill - by EdK - 08-01-2016, 04:21 PM
RE: home made mill - by oldskoolron - 08-19-2016, 05:26 AM
RE: home made mill - by krv3000 - 10-01-2016, 02:16 PM
RE: home made mill - by Mayhem - 10-01-2016, 09:24 PM
RE: home made mill - by EdK - 10-02-2016, 09:27 AM
RE: home made mill - by Roadracer_Al - 10-02-2016, 11:33 AM
RE: home made mill - by Dr Stan - 10-14-2016, 07:07 PM
RE: home made mill - by krv3000 - 10-13-2016, 04:11 PM
RE: home made mill - by Micktoon - 10-13-2016, 04:27 PM
RE: home made mill - by krv3000 - 10-14-2016, 05:42 PM
RE: home made mill - by RobWilson - 10-15-2016, 02:26 AM
RE: home made mill - by krv3000 - 10-22-2016, 02:53 PM
RE: home made mill - by krv3000 - 10-29-2016, 04:08 PM
RE: home made mill - by Micktoon - 10-30-2016, 05:14 AM
RE: home made mill - by krv3000 - 10-30-2016, 06:10 PM
RE: home made mill - by krv3000 - 12-03-2016, 06:39 AM
RE: home made mill - by pepi - 12-03-2016, 07:19 AM
RE: home made mill - by TomG - 12-03-2016, 11:55 AM
RE: home made mill - by krv3000 - 12-03-2016, 01:20 PM
RE: home made mill - by f350ca - 12-03-2016, 01:25 PM
RE: home made mill - by awemawson - 12-03-2016, 01:46 PM
RE: home made mill - by Dr Stan - 12-03-2016, 02:18 PM
RE: home made mill - by awemawson - 12-03-2016, 03:01 PM
RE: home made mill - by krv3000 - 12-04-2016, 03:49 AM
RE: home made mill - by krv3000 - 12-11-2016, 05:50 PM
RE: home made mill - by Seanlogie - 02-05-2017, 03:57 AM
RE: home made mill - by krv3000 - 02-06-2017, 05:40 PM
RE: home made mill - by Micktoon - 02-06-2017, 05:53 PM
RE: home made mill - by Mayhem - 02-07-2017, 05:55 AM
RE: home made mill - by krv3000 - 02-07-2017, 06:03 PM
RE: home made mill - by wawoodman - 02-07-2017, 07:03 PM
RE: home made mill - by krv3000 - 02-08-2017, 05:19 PM
RE: home made mill - by krv3000 - 02-12-2017, 12:56 PM
RE: home made mill - by Micktoon - 02-12-2017, 04:05 PM
RE: home made mill - by krv3000 - 02-20-2017, 06:58 PM
RE: home made mill - by Mayhem - 02-21-2017, 06:55 AM
RE: home made mill - by krv3000 - 02-21-2017, 02:44 PM
RE: home made mill - by Pete O - 02-21-2017, 04:40 PM
RE: home made mill - by krv3000 - 02-22-2017, 07:58 PM
RE: home made mill - by Pete O - 02-23-2017, 06:13 PM
RE: home made mill - by Pete O - 02-23-2017, 06:25 PM
RE: home made mill - by Mayhem - 02-24-2017, 06:55 AM
RE: home made mill - by krv3000 - 02-24-2017, 04:52 PM
RE: home made mill - by krv3000 - 02-27-2017, 05:43 PM



Users browsing this thread: 1 Guest(s)