MetalworkingFun Forum › Machining › Projects v
mill vise

Thread Modes
mill vise
Dr Stan Offline
Senior
*****
Posts: 2,324
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
#17
03-20-2018, 03:02 PM (This post was last modified: 03-20-2018, 03:07 PM by Dr Stan.)
(03-20-2018, 02:13 PM)Vinny Wrote: The vise Shars has?  The more than likely Chinese version of the one in the original post.

[Image: 202-1027Main.jpg]
This is the only one I could find and comes in 6 and 8 inch versions. At first I thought it was a piston type clamping vice.  After I looked at the same thing at Travers I realized it tightens with a screw.  I don't have a lot of faith in the piston type vices.
Reply
Thanks given by:


Messages In This Thread
mill vise - by Vinny - 02-18-2018, 11:12 AM
RE: mill vise - by Hawkeye - 02-18-2018, 11:17 AM
RE: mill vise - by SteveG - 02-18-2018, 07:41 PM
RE: mill vise - by f350ca - 02-18-2018, 08:53 PM
RE: mill vise - by pepi - 02-18-2018, 10:15 PM
RE: mill vise - by randyc - 02-18-2018, 11:57 PM
RE: mill vise - by the penguin - 02-19-2018, 11:18 AM
RE: mill vise - by the penguin - 02-19-2018, 11:27 AM
RE: mill vise - by randyc - 02-19-2018, 04:18 PM
RE: mill vise - by randyc - 02-19-2018, 05:39 PM
RE: mill vise - by SteveG - 02-19-2018, 06:01 PM
RE: mill vise - by randyc - 02-19-2018, 10:24 PM
RE: mill vise - by Vinny - 02-20-2018, 12:04 AM
RE: mill vise - by Dr Stan - 03-20-2018, 11:57 AM
RE: mill vise - by 2Young2 - 03-18-2018, 11:14 AM
RE: mill vise - by Vinny - 03-20-2018, 02:13 PM
RE: mill vise - by Dr Stan - 03-20-2018, 03:02 PM
RE: mill vise - by Vinny - 03-20-2018, 06:36 PM
RE: mill vise - by Dr Stan - 03-20-2018, 08:54 PM
RE: mill vise - by EdK - 03-21-2018, 03:51 PM
RE: mill vise - by Vinny - 03-20-2018, 10:50 PM
RE: mill vise - by Dr Stan - 03-21-2018, 02:10 PM
RE: mill vise - by Mike E. - 07-28-2018, 09:28 AM
RE: mill vise - by Vinny - 07-28-2018, 11:45 AM
RE: mill vise - by Highpower - 07-31-2018, 03:35 PM
RE: mill vise - by Highpower - 07-28-2018, 04:15 PM
RE: mill vise - by Mike E. - 07-29-2018, 05:48 AM
RE: mill vise - by Vinny - 07-31-2018, 06:35 PM
RE: mill vise - by big o - 08-05-2021, 06:08 PM
RE: mill vise - by Vinny - 08-05-2021, 09:35 PM
RE: mill vise - by Dr Stan - 08-07-2021, 01:36 PM
RE: mill vise - by Vinny - 08-09-2021, 09:16 PM



Users browsing this thread: 1 Guest(s)