Part support while milling

Hello There, Guest! Register

Thread Modes

Part support while milling

Vinny

Online

Another Whipping Boy

Posts: 2,596
Threads: 99
Joined: Dec 2014
Location: Michigan

#12

10-24-2019, 02:02 PM

With Speedy, if you call sales and place your order the prices are CONSIDERABLY lower. Shipping still sux tho. I had ordered some 1/8" thick 3-1/2 x 48" from Xometry, it was about $14 (for 2) after the discount and shipping was free. It showed up today. Well packed, shipped FedEx ground. Was here at 8:30 this am. I have a couple of mobile antenna mounts to make, the needed endmill is due here tomorrow.

Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop | the nobucks boutique

Website

Reply

Thanks given by: Highpower

« Next Oldest | Next Newest »

Messages In This Thread

Part support while milling - by Paulc - 10-22-2019, 09:17 PM

RE: Part support while milling - by Hawkeye - 10-22-2019, 10:22 PM

RE: Part support while milling - by Highpower - 10-22-2019, 11:15 PM

RE: Part support while milling - by rleete - 10-23-2019, 10:08 AM

RE: Part support while milling - by Paulc - 10-23-2019, 11:29 AM

RE: Part support while milling - by Vinny - 10-23-2019, 02:40 PM

RE: Part support while milling - by Highpower - 10-23-2019, 11:10 PM

RE: Part support while milling - by Paulc - 10-23-2019, 02:44 PM

RE: Part support while milling - by Highpower - 10-23-2019, 07:35 PM

RE: Part support while milling - by Paulc - 10-23-2019, 08:47 PM

RE: Part support while milling - by TomG - 10-23-2019, 10:59 PM

RE: Part support while milling - by Vinny - 10-24-2019, 02:02 PM

RE: Part support while milling - by Highpower - 10-24-2019, 07:15 PM

RE: Part support while milling - by Vinny - 10-24-2019, 11:13 PM

RE: Part support while milling - by Highpower - 10-25-2019, 09:30 AM

RE: Part support while milling - by f350ca - 10-25-2019, 02:01 PM

RE: Part support while milling - by Highpower - 10-25-2019, 04:15 PM

RE: Part support while milling - by f350ca - 10-25-2019, 05:12 PM

RE: Part support while milling - by Highpower - 10-25-2019, 11:57 PM

RE: Part support while milling - by Highpower - 10-29-2019, 08:46 AM

RE: Part support while milling - by Paulc - 10-29-2019, 12:44 PM

RE: Part support while milling - by Dr Stan - 10-29-2019, 12:47 PM

RE: Part support while milling - by Paulc - 10-29-2019, 02:39 PM

RE: Part support while milling - by Highpower - 10-29-2019, 03:47 PM

RE: Part support while milling - by Paulc - 10-29-2019, 10:34 PM

RE: Part support while milling - by Highpower - 10-30-2019, 06:23 AM

RE: Part support while milling - by Paulc - 10-30-2019, 09:46 PM

RE: Part support while milling - by Vinny - 11-01-2019, 02:54 PM

RE: Part support while milling - by Highpower - 11-01-2019, 11:41 PM

RE: Part support while milling - by Vinny - 11-03-2019, 06:37 PM

RE: Part support while milling - by rleete - 11-04-2019, 09:17 AM

Users browsing this thread: 1 Guest(s)