My week this week! My workshop videos!
#61
Video 
In which I finish the bench for the Jones and Shipman bench centres, finish the adapter for the pipe bender, and actually get back to bending the exhaust for the Toro 2CV tractor, which I started about 4 weeks ago!  In another lifetime at school, I only once got lines, and mine were "I must concentrate on the job in hand" That teacher knew me really well!!
Phil, in Wintry East Yorkshire.


Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
Reply
Thanks given by:
#62
I get at least half of the exhaust done, and the other half planned, and then I fit the grass deck and realise that there is nowhere near as much free space now, and when the grass deck and the front axle pivot from side to side to follow the terrain, most of that free space dissapears anyway! I have to rethink the other half. See it big, keep it simple!
Phil, in misty mysterious East Yorkshire


Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
Reply
Thanks given by:
#63


This week I actualy finish the exhaust I have been  procrastinating for nearly two weeks over it, and as my late mate Alfred would have said,  in his thick Dutch accent, procrastination is the thief of time". I will do better now that is out of the way!
Phil, in unseasonably mild East Yorkshire.
https://youtu.be/eDxIc5FvBm0
Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
Reply
Thanks given by:
#64
The last gasp up to the holidays, but I gopt far more dome than I thought I would, and have got even more ideas for after Christmas, I will be back in the shop in early January, unless it snows, in which case it is anybodies guess as the Langtoft road is particularly treachorous in snow, and it can block up and be impassable in less than 30 minutes! As I type this there is a storm brewing which will bring Greenlands weather straight onto the west coast of the UK, so snow could be a distinct possibility! Have a good holiday and keep safe! All the best!
Phil, in a distinctly colder East Yorkshire



Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
Reply
Thanks given by:
#65
Hope you have all had a good time and are refreshed and relaxed and ready to brave the weather and go back to work? No neuther sm I!! I am taking eldest back to Uni on the 6th(thats the plan at the moment anyway) and will be back in the workshop for more fun and games on the 11th, Thanks you all for watching, please subscribe and comment, and all of you stay safe and lets have a better 2021!
Phil


Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
Reply
Thanks given by:
#66
Well folks, I dragged myself back to work after a pleasant Christmas break, got the air filter finished, and made progres generally, but then, the starter is no longer able to spin the engine! that will teach me not to to fit new rings, and grind the valves in! Too much compression for a starter that is designed to start a 15hp single cylinder engine! I think I have pushed the boat out too far, and too fast, and then tried to jump in, and the obvious has happened! The new starter arrives tomorrow! Thanks for watching, and a strappy new year to you all!
Phil Slip sliding away on the ice in East Yorkshire.


Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
Reply
Thanks given by:
#67
Its on! The week went quite well after I stopped procrastinating and just got on and did it! Another breakthrough was the fact that I realised that the vee belt was dragging in the pulley, and stopping the engine spinning properly at start up. This is the belt which is the correct size for the clutch drive, but is obviously too tight for jockey pulley running, I need to see my belt man and get one a couple of inches longer. Thanks for watching, please like and subscribe!
Phil,   In frosty but fine East Yorkshire!


Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
Reply
Thanks given by:
#68
Another week of finishing off and troubleshooting on the Toro 2CV. I eventually got to the bottom of the carb fault, but it meant taking the carb body off again, which means it is going to get a thorough clean and shakedown before it goes back on. Thanks for watching, and don't forget to subscribe, like and comment!
Phil, in soggy East Yorkshire


Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
Reply
Thanks given by:
#69
Video 
At last! The engine, mainly the carburettor, is sorted. multiple problems have been fixed, and now she starts easily, ticks over slowly and throttles up smoothly. I can now get on with the finishing off! Need new alternator bearings, they are noisy, and the new coil will arrive next week. If only I could find that ignition switch!!! Thanks for watching, please subscribe and comment.
Phil, East Yorkshire has snow and ice warnings!!

Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
Reply
Thanks given by:
#70
Well folks, the week started badly, with bitter cold and snow, and ended better, with bitter cold, snow, and a new to me Holbrook Model B Number 9!! It must be said that a lathe is about the only thing that would get me out in this weather, and I nearly froze, but it was worth it!  The lathe is now stripped, and all the bits are at the workshop, except the bed, chip pan and legs, which we will collect next week, with the big trailer. Thank you all for watching, please comment, like and subscribe, and don't forget to ring the bell, or you wont get notified when a new video comes out!
Phil. Perishing cold East Yorkshire


Man who say it cannot be done should not disturb man doing it! https://www.youtube.com/user/philhermetic/videos?
Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)