Mill X-axis Powerfeed for G08689
#25
I found a 200 RPM gearmotor at DigiKey, but it only has about 1.5 ft-lbs of torque; I'm not sure that will be enough. The problem arises when you get those small motors that the torque falls off as the speed increases. So, getting decent speeds for a fast return means too little torque at lower speeds such as for milling.

But after searching for several days, I think I have found a solution. It is going to require some creative engineering (Rube Goldberg) to mount, but I think it should work. Pictures to follow as I get parts in hand to test.
Full of ideas, but slow to produce parts
Reply
Thanks given by:


Messages In This Thread
Mill X-axis Powerfeed for G08689 - by rleete - 04-22-2023, 03:33 PM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 04-23-2023, 12:38 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 04-23-2023, 07:56 AM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 04-23-2023, 11:16 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 04-24-2023, 11:04 AM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 04-24-2023, 10:28 PM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 04-25-2023, 05:48 AM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 05-04-2023, 03:21 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 05-04-2023, 06:16 AM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 05-04-2023, 08:59 PM
RE: Mill X-axis Powerfeed for G08689 - by Vinny - 05-04-2023, 09:35 PM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 05-04-2023, 10:13 PM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 05-05-2023, 03:39 PM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 05-05-2023, 06:31 PM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 05-11-2023, 03:33 PM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 06-03-2023, 12:51 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 06-03-2023, 07:39 AM
RE: Mill X-axis Powerfeed for G08689 - by BaronJ - 02-28-2024, 09:32 AM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 02-28-2024, 11:53 AM
RE: Mill X-axis Powerfeed for G08689 - by BaronJ - 02-28-2024, 02:27 PM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 02-28-2024, 02:40 PM
RE: Mill X-axis Powerfeed for G08689 - by BaronJ - 02-29-2024, 05:08 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 03-22-2024, 06:17 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 03-22-2024, 10:16 AM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 03-22-2024, 11:32 AM
RE: Mill X-axis Powerfeed for G08689 - by rleete - 03-23-2024, 05:02 PM
RE: Mill X-axis Powerfeed for G08689 - by EdK - 03-23-2024, 11:40 PM
RE: Mill X-axis Powerfeed for G08689 - by rubes - 03-24-2024, 09:45 AM



Users browsing this thread: 2 Guest(s)