MetalworkingFun Forum › Machinery › Milling Machines v
Kondia FV-1 Table/Saddle/Knee/Turret and Ram removal

Thread Modes
Kondia FV-1 Table/Saddle/Knee/Turret and Ram removal
Highpower Offline
JAFO
******
Posts: 4,369
Threads: 178
Joined: Feb 2012
Location: Missouri, USA
#45
05-18-2014, 12:20 PM (This post was last modified: 05-18-2014, 01:43 PM by Highpower.)
(05-17-2014, 11:48 PM)Mayhem Wrote: ... So I'm thinking of a large diameter washer (same size as the other end of the pin) and a cleaned up nut will work fine for me.

I think I have a box full of brand new 22 and 24mm flanged nuts somewhere around here. (Honda axle nuts.) Chin

I'll have to do some digging....

Edit to add:
Found the box. Yikes
Just shoot me your shipping address in a PM if you want it Darrin.

   
Willie
Reply
Thanks given by: Mayhem


Messages In This Thread
RE: Removing a table from a mill - by TomG - 06-19-2012, 08:03 AM
RE: Removing a table from a mill - by Bill Gruby - 06-19-2012, 08:22 AM
RE: Removing a table from a mill - by Mayhem - 06-19-2012, 08:51 AM
RE: Removing a table from a mill - by TomG - 06-19-2012, 09:33 AM
RE: Removing a table from a mill - by ScrapMetal - 06-19-2012, 01:57 PM
RE: Removing a table from a mill - by EdK - 06-19-2012, 04:49 PM
RE: Removing a table from a mill - by f350ca - 06-19-2012, 07:19 PM
RE: Removing a table from a mill - by Mayhem - 06-20-2012, 12:42 AM
RE: Removing a table from a mill - by stevec - 06-20-2012, 01:38 PM
RE: Removing a table from a mill - by ScrapMetal - 06-20-2012, 03:09 PM
RE: Removing a table from a mill - by doubleboost - 06-20-2012, 03:18 PM
RE: Removing a table from a mill - by ScrapMetal - 06-20-2012, 07:17 PM
RE: Removing a table from a mill - by stevec - 06-21-2012, 07:26 AM
RE: Removing a table from a mill - by ScrapMetal - 06-21-2012, 07:50 PM
RE: Removing a table from a mill - by arvidj - 06-21-2012, 07:18 PM
RE: Removing a table from a mill - by November X-ray - 06-22-2012, 05:26 AM
RE: Removing a table from a mill - by Mayhem - 06-22-2012, 06:12 AM
RE: Removing a table from a mill - by ScrapMetal - 06-22-2012, 02:54 PM
RE: Removing a table from a mill - by Mayhem - 06-22-2012, 09:48 PM
RE: Kondia FV-1 Table removal - by Mayhem - 10-21-2012, 06:09 AM
RE: Kondia FV-1 Table removal - by Mayhem - 10-31-2012, 07:04 PM
RE: Kondia FV-1 Table removal - by Mayhem - 11-01-2012, 09:51 AM
RE: Kondia FV-1 Table removal - by Highpower - 11-04-2012, 06:48 AM
RE: Kondia FV-1 Table removal - by TomG - 11-02-2012, 06:31 AM
RE: Kondia FV-1 Table/Saddle/Knee/Turret and Ram removal - by Highpower - 05-18-2014, 12:20 PM



Users browsing this thread: 3 Guest(s)