MetalworkingFun Forum › Machining › Projects v
mini mill

Thread Modes
mini mill
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
#24
07-15-2012, 07:27 AM (This post was last modified: 07-15-2012, 08:11 AM by dallen.)
(07-15-2012, 06:28 AM)DaveH Wrote: DA,
That seems a favourite past time for gibs, they either touch at the ends or just in the middle Rotfl
Smiley-eatdrink004
DaveH

unless you make them flat Thumbsup this is the same gib just without most of the scratch, all that is left of it is within the blue circle.

The other piece that is in the photo is a prism that I cut out on my little 7 inch shaper yesterday and have been working on with the scraper and surface plate. Its starting to get pretty flat now but I still have a ways to go.

   
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:


Messages In This Thread
mini mill - by dallen - 07-07-2012, 10:50 PM
RE: mini mill - by Highpower - 07-08-2012, 07:33 AM
RE: mini mill - by DaveH - 07-08-2012, 11:12 AM
RE: mini mill - by ETC57 - 07-08-2012, 11:20 AM
RE: mini mill - by henryarnold - 07-08-2012, 12:23 PM
RE: mini mill - by dallen - 07-08-2012, 01:20 PM
RE: mini mill - by Mayhem - 07-09-2012, 04:28 AM
RE: mini mill - by dallen - 07-09-2012, 11:40 AM
RE: mini mill - by dallen - 07-11-2012, 09:15 PM
RE: mini mill - by dallen - 07-12-2012, 01:19 AM
RE: mini mill - by DaveH - 07-12-2012, 08:31 AM
RE: mini mill - by dallen - 07-12-2012, 05:28 PM
RE: mini mill - by ETC57 - 07-12-2012, 06:23 PM
RE: mini mill - by dallen - 07-12-2012, 10:20 PM
RE: mini mill - by Mayhem - 07-12-2012, 08:17 PM
RE: mini mill - by dallen - 07-12-2012, 10:12 PM
RE: mini mill - by ETC57 - 07-12-2012, 10:46 PM
RE: mini mill - by dallen - 07-13-2012, 11:01 PM
RE: mini mill - by dallen - 07-12-2012, 10:57 PM
RE: mini mill - by dallen - 07-13-2012, 07:51 AM
RE: mini mill - by DaveH - 07-14-2012, 06:03 AM
RE: mini mill - by dallen - 07-14-2012, 09:11 PM
RE: mini mill - by DaveH - 07-15-2012, 06:28 AM
RE: mini mill - by dallen - 07-15-2012, 07:27 AM
RE: mini mill - by Rickabilly - 07-16-2012, 09:12 PM
RE: mini mill - by dallen - 07-17-2012, 07:12 AM
RE: mini mill - by Rickabilly - 07-17-2012, 08:55 AM
RE: mini mill - by Highpower - 07-17-2012, 09:34 AM
RE: mini mill - by dallen - 07-17-2012, 12:23 PM
RE: mini mill - by DaveH - 07-17-2012, 02:12 PM
RE: mini mill - by Rickabilly - 07-17-2012, 10:53 PM
RE: mini mill - by Mayhem - 07-18-2012, 06:32 AM
RE: mini mill - by Rickabilly - 07-18-2012, 07:20 AM
RE: mini mill - by Mayhem - 07-18-2012, 07:33 AM
RE: mini mill - by dallen - 07-20-2012, 07:23 AM
RE: mini mill - by Rickabilly - 07-21-2012, 02:53 AM
RE: mini mill - by Rickabilly - 07-21-2012, 09:19 AM
RE: mini mill - by Mayhem - 07-21-2012, 09:55 AM
RE: mini mill - by dallen - 07-21-2012, 11:32 AM
RE: mini mill - by Rickabilly - 07-22-2012, 06:48 AM
RE: mini mill - by dallen - 07-22-2012, 08:43 AM
RE: mini mill - by NevadaBlue - 07-22-2012, 07:19 PM
RE: mini mill - by DaveH - 07-22-2012, 07:28 PM
RE: mini mill - by NevadaBlue - 07-22-2012, 07:37 PM
RE: mini mill - by EdK - 07-23-2012, 05:29 AM
RE: mini mill - by dallen - 07-22-2012, 08:49 PM
RE: mini mill - by NevadaBlue - 07-23-2012, 12:39 AM
RE: mini mill - by dallen - 07-23-2012, 07:07 AM
RE: mini mill - by Rickabilly - 07-23-2012, 02:12 PM
RE: mini mill - by EdK - 07-23-2012, 03:47 PM
RE: mini mill - by NevadaBlue - 07-24-2012, 07:00 PM
RE: mini mill - by Mayhem - 07-24-2012, 07:17 PM
RE: mini mill - by Highpower - 07-25-2012, 09:26 AM
RE: mini mill - by dallen - 07-25-2012, 10:16 AM
RE: mini mill - by Highpower - 07-25-2012, 10:37 AM
RE: mini mill - by dallen - 07-25-2012, 11:39 AM
RE: mini mill - by Rickabilly - 07-25-2012, 02:35 PM
RE: mini mill - by Highpower - 07-25-2012, 04:09 PM
RE: mini mill - by EdK - 07-25-2012, 04:18 PM
RE: mini mill - by dallen - 07-25-2012, 04:21 PM
RE: mini mill - by Mayhem - 07-26-2012, 05:02 AM
RE: mini mill - by Rickabilly - 07-27-2012, 03:21 AM
RE: mini mill - by Mayhem - 07-27-2012, 12:30 AM
RE: mini mill - by dallen - 08-01-2012, 11:41 AM
RE: mini mill - by Mayhem - 08-01-2012, 07:37 PM
RE: mini mill - by dallen - 08-01-2012, 09:13 PM



Users browsing this thread: 1 Guest(s)