MetalworkingFun Forum › Machinery › Lathes v
Wedge type QCTP

Thread Modes
Wedge type QCTP
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
#10
09-08-2012, 01:41 PM
(09-08-2012, 08:07 AM)dalee Wrote: I think the reason the tee nuts get hardened is to make the threads last. As you loosen and tighten the post to tweak it around, over time the threads will wear and may get pulled and damaged if left soft. Harden them a bit and chance of damage is lessened.

dalee
I'm pretty sure the rod through the post shouldn't be turning in the "T" nut. It should be the nut on top, the one some of us nuts keep misplacing the wrench for.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:


Messages In This Thread
Wedge type QCTP - by stevec - 09-07-2012, 06:35 PM
RE: Wedge type QCTP - by EdK - 09-07-2012, 06:44 PM
RE: Wedge type QCTP - by Highpower - 09-07-2012, 09:11 PM
RE: Wedge type QCTP - by Kaoma - 09-07-2012, 11:53 PM
RE: Wedge type QCTP - by EdK - 09-08-2012, 08:41 AM
RE: Wedge type QCTP - by Wawoodman - 09-08-2012, 12:02 AM
RE: Wedge type QCTP - by big job - 09-08-2012, 05:30 AM
RE: Wedge type QCTP - by dalee - 09-08-2012, 08:07 AM
RE: Wedge type QCTP - by stevec - 09-08-2012, 01:41 PM
RE: Wedge type QCTP - by dalee - 09-09-2012, 01:52 PM
RE: Wedge type QCTP - by Highpower - 09-08-2012, 11:41 AM
RE: Wedge type QCTP - by Kaoma - 09-09-2012, 12:59 PM
RE: Wedge type QCTP - by rleete - 09-09-2012, 01:18 PM
RE: Wedge type QCTP - by f350ca - 09-09-2012, 01:32 PM
RE: Wedge type QCTP - by DaveH - 09-09-2012, 02:37 PM
RE: Wedge type QCTP - by Kaoma - 09-09-2012, 02:39 PM
RE: Wedge type QCTP - by EdK - 09-09-2012, 05:25 PM
RE: Wedge type QCTP - by doubleboost - 09-09-2012, 03:21 PM
RE: Wedge type QCTP - by stevec - 09-09-2012, 03:24 PM
RE: Wedge type QCTP - by stevec - 09-09-2012, 03:28 PM
RE: Wedge type QCTP - by doubleboost - 09-09-2012, 03:41 PM
RE: Wedge type QCTP - by stevec - 09-09-2012, 05:34 PM
RE: Wedge type QCTP - by PixMan - 09-09-2012, 08:26 PM
RE: Wedge type QCTP - by Kaoma - 09-09-2012, 09:17 PM
RE: Wedge type QCTP - by EdK - 09-10-2012, 09:26 AM
RE: Wedge type QCTP - by f350ca - 09-09-2012, 09:51 PM
RE: Wedge type QCTP - by Mayhem - 09-10-2012, 05:07 AM
RE: Wedge type QCTP - by PixMan - 09-10-2012, 06:20 AM
RE: Wedge type QCTP - by Mayhem - 09-10-2012, 09:43 AM
RE: Wedge type QCTP - by SnailPowered - 09-10-2012, 11:38 AM
RE: Wedge type QCTP - by stevec - 09-10-2012, 02:18 PM
RE: Wedge type QCTP - by EdK - 09-10-2012, 03:29 PM
RE: Wedge type QCTP - by stevec - 09-10-2012, 06:43 PM
RE: Wedge type QCTP - by stevec - 09-19-2012, 11:22 AM
RE: Wedge type QCTP - by EdK - 09-19-2012, 12:00 PM
RE: Wedge type QCTP - by stevec - 09-19-2012, 01:25 PM
RE: Wedge type QCTP - by DaveH - 09-19-2012, 01:34 PM
RE: Wedge type QCTP - by dallen - 09-19-2012, 01:45 PM
RE: Wedge type QCTP - by f350ca - 09-19-2012, 04:43 PM
RE: Wedge type QCTP - by stevec - 09-20-2012, 01:39 PM
RE: Wedge type QCTP - by EdK - 09-20-2012, 04:47 PM
RE: Wedge type QCTP - by stevec - 09-20-2012, 06:26 PM
RE: Wedge type QCTP - by stevec - 09-22-2012, 04:24 PM



Users browsing this thread: 2 Guest(s)