MetalworkingFun Forum › Machinery › Lathes v
Gib locking & DRO

Thread Modes
Gib locking & DRO
petertha Offline
Freshman
**
Posts: 32
Threads: 3
Joined: Sep 2012
Location: Calgary, AB, Canada
#16
10-31-2012, 12:02 AM (This post was last modified: 10-31-2012, 12:10 AM by petertha.)
Here are some pics. I replaced the cheesy wing nut with a slightly less cheesy knurled knob. Monkey see monkey do, didnt know better at the time. Is this the general idea of the pin type contact slider pad?


Attached Files Thumbnail(s)
   

.jpg   2012-10-30_230900.jpg (Size: 7.88 KB / Downloads: 41)
.jpg   2012-10-30_224611.jpg (Size: 39.52 KB / Downloads: 42)
.jpg   2012-10-30_230920.jpg (Size: 7.48 KB / Downloads: 41)
petertha, proud to be a member of MetalworkingFun since Sep 2012.
Reply
Thanks given by:


Messages In This Thread
Gib locking & DRO - by petertha - 10-29-2012, 01:26 PM
RE: Gib locking & DRO - by EdK - 10-29-2012, 04:37 PM
RE: Gib locking & DRO - by petertha - 10-29-2012, 10:57 PM
RE: Gib locking & DRO - by TomG - 10-30-2012, 06:37 AM
RE: Gib locking & DRO - by EdK - 10-30-2012, 07:00 AM
RE: Gib locking & DRO - by TomG - 10-30-2012, 08:21 AM
RE: Gib locking & DRO - by stevec - 10-30-2012, 08:43 AM
RE: Gib locking & DRO - by TomG - 10-30-2012, 10:02 AM
RE: Gib locking & DRO - by EdK - 10-30-2012, 09:36 AM
RE: Gib locking & DRO - by Mayhem - 10-30-2012, 10:25 AM
RE: Gib locking & DRO - by EdK - 10-30-2012, 11:02 AM
RE: Gib locking & DRO - by stevec - 10-30-2012, 12:37 PM
RE: Gib locking & DRO - by TomG - 10-30-2012, 01:55 PM
RE: Gib locking & DRO - by EdK - 10-30-2012, 05:14 PM
RE: Gib locking & DRO - by Dave J - 10-30-2012, 07:38 PM
RE: Gib locking & DRO - by EdK - 10-31-2012, 05:59 AM
RE: Gib locking & DRO - by Dave J - 10-31-2012, 08:37 PM
RE: Gib locking & DRO - by petertha - 10-31-2012, 12:02 AM
RE: Gib locking & DRO - by EdK - 10-31-2012, 05:59 AM
RE: Gib locking & DRO - by Dave J - 10-31-2012, 08:39 PM
RE: Gib locking & DRO - by TomG - 10-31-2012, 07:00 AM
RE: Gib locking & DRO - by Mayhem - 11-01-2012, 10:03 AM



Users browsing this thread: