Fire Wood Processor
Just seeing if we have this figured out. 

Hubs for the idler sprockets on the live deck.

[Image: twI0gzhOhGJ_UKrGzDnHDM5fmnQlBMgokmxIKmNd...3-h1243-no]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
(08-06-2016, 12:39 PM)Black Forest Wrote: On Monday I will fell 21 trees.  The minimum diameter is 400mm the largest is 750mm.   They are destined to become firewood.  

Soooooooooooo  Greg..............


BF, where do you find 21 trees in Germany? Blush

Rotfl
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
(08-07-2016, 07:05 AM)stevec Wrote:
(08-06-2016, 12:39 PM)Black Forest Wrote: On Monday I will fell 21 trees.  The minimum diameter is 400mm the largest is 750mm.   They are destined to become firewood.  

Soooooooooooo  Greg..............


BF, where do you find 21 trees in Germany? Blush

Rotfl

I am guessing you have never been to the Black Forest in Germany. It is called that because the tree canopy is so dense that it is dark in the forest.
Reply
Thanks given by:
Still too humid to open the shop doors so I've been working inside. The log deck would have been a lot easier to build spread out, but we built it in the folded position. Had to get all the bunks square and level before welding so they'd hopefully open up properly.
Found a piece of 1 3/8 4 tpi acme rod, believe it was for levelling scaffolding. I made a 4 inch deep nut that was then cut in 3 for levelling the legs.
[Image: uf6mM5rXIZJ_NQ6osfbfkxi44sTU0EExHOCX5KEx...0-h1266-no]

The log deck folded for transport. Had to make a double jointed hinge to get it to fold 180 degrees.

[Image: STnhZIe20kLw_sH2E8GnHR0klFV_WoIJmMzlDugn...0-h1266-no]

Now I need to get it outside to install the roller chains for moving the logs.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
If you drive fast the air won't even notice you opened the doors until you close them again! You could even use your mule to drag it outside.
Reply
Thanks given by:
Was dry enough today to open the shop. Looks like the hinge system works. 
[Image: YI5qw41717OF2N46RpkndeDSudlEZHd5r6ARVSbp...8-h1266-no]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
looking good Greg
Reply
Thanks given by:
Outstanding Greg!!!!
Reply
Thanks given by:
Got the oiler for the chain saw working so it was time for a proper test. 
The log deck still needed the chain on the centre bunk, once it was installed the logs feed properly.
The chute the log drops into still needs planking to centre the log when it rolls in.
The feed chain on the log chute is too slow, will have to change the ratio on the drive chain to sort that out.
The saw works great, I was worried the single belt drive would slip but that isn't an issue at all. In fact I managed to clamp the log too tight and bound the saw, it will stall the engine.
The cut block hangs up on the saw guard as it rolls over to the splitter. Not sure there is much I can do about that. Not a huge issue, think I can live with it.
The splitter is great. Fast and powerful. As you can see 30 inch long oak blocks are pretty much a joke for it.
All in all I'm pleased.
Couple of little things to finish up and we should be painting it latter
this week.

https://www.youtube.com/watch?v=ovAi-dd0dKY

Thanks for watching
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
Heck of a machine there Greg. Mighty impressive for something built from scratch in a home shop. Worthy
Willie
Reply
Thanks given by:




Users browsing this thread: 3 Guest(s)