New Log Splitter
#41
Steve,

Is that boat for fishing, hunting or both? I use to fish a lot but haven't in decades. I hope to get back to it when I retire.

Oh, and nice progress on the log splitter.

Ed
Reply
Thanks given by:
#42
Fishing Ed, I haven't hunted in almost 15 years. It was deer hunting and I never shot one although my group always got at least one every year. Just found it to be more of a chore of misery than it was worth.
Steve (the wimp)
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#43
You'll be able to split the trunk in one shot with that monster.

"Billy G"
Reply
Thanks given by:
#44
Billy G, that's the plan.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#45
More progress! The changeable wedge now has it's backer installed,
The Cylinder mount is mounted and the hydraulic tank/axle is tacked on (only tacked--just in case there's a positional adjustment required).
   
Oh yeah, the hitch mount is fabbed and welded on.
   
Here's a pick of a cyl. mount fillet weld, 5/32" 7014 rod at 160 amps.
   

I started to mock up the engine and pump mounting and revisited the pump mount that I'd fabbed, somehow my addled mind decided that the mount was too long and would require that the lovejoy coupling halves would need to be extended beyond their shafts so I decided to shorten the mount I had made. I cut out the calculated (miscalculated) extra and machined the cuts so the reweld would have a modicum of alignment.

A beer and lunch sent me back to the shop where I realized I'd forgotten to include the rubber spider between the lovejoy halves Jawdrop
So remanufacture of the engine/pump mounting adapter was begun.

Things really started to slide here (shoulda had TWO beers with lunch).

I needed my 4 jaw to reface the motor flange and being too weak to mount the D1-6 four jaw on the 16-60 I decided to unscrew the 3 jaw from my ole 12X37.
I unscrewed the jaws of the 3 jaw so a projection could interfere with it's reverse direction and unscrew the chuck when I slipped a 2 x 6 in between a protruding jaw and the rear way of the bed.
What I succeeded in doing was to strip a few teeth of one of the delrin gears in my gearhead conversion.
   
I guess I'll hafta put the heavy 4 jaw on the 16X60 to get the job at hand done.
An appointment with the gear dentist (me) will have to be arranged.

More to come on the splitter and a new thread will appear on "Steve's dental service for Delrin gears.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#46
(05-12-2013, 05:12 PM)stevec Wrote: More progress! The changeable wedge now has it's backer installed,

Log splitter? It looks like you could slice an engine block in half with that thing. Yikes

Good looking welds there Dr. Steve. Smiley-eatdrink004
Willie
Reply
Thanks given by: stevec
#47
Those are nice welds Steve. I look forward to your "Steve's dental service for Delrin gears" thread.

Ed
Reply
Thanks given by:
#48
Almost ready for testing.
I need to measure up for the hydraulic lines, disassemble, paint and reassemble.

       

   

Ed, the frame that's lying on the floor, part of the log lifter is what was in the framing clamp of my other post.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by: EdK
#49
Looking good Steve
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
#50
looking good,, but,,, why is that shop floor so tidy?????????????
sasquatch, proud to be a member of MetalworkingFun since Jul 2012.
Reply
Thanks given by:




Users browsing this thread: 3 Guest(s)