MetalworkingFun Forum › Machining › CNC v
Knurling Vial Caps

Thread Modes
Knurling Vial Caps
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
The following 1 user Likes stevec's post:
EdK (10-16-2013)
#11
10-16-2013, 03:30 PM (This post was last modified: 10-16-2013, 03:31 PM by stevec.)
Ed, I found the HSM issue and was able to determine that the gears link the 2 spindle housings so that they rotate equally when the cutter "opening" is adjusted. Chin
I see now the cutters are freewheeling, I initially thought the gears might "time" the cutters to keep the crosshatch consistent. Slaphead
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
krv3000 Offline
Senior
*****
Posts: 1,520
Threads: 157
Joined: Feb 2012
Location: uk
#12
10-17-2013, 03:47 PM
Very nice Russ
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by: wrustle
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#13
10-17-2013, 06:11 PM
The swiveling angle of the knurl (wheel) holders doesn't need to be geared, IMHO that's overkill. All you need is a single reference line that's located on the same point on each of the angled holders. Then you would scribe lines on the body those rotate on, marking at 0º, 30º, 45º and 60º. This allows you to make true diamond patterns of any angle, square, or straight knurls.
Reply
Thanks given by:
wrustle Offline
Junior
****
Posts: 438
Threads: 67
Joined: Sep 2012
Location: Central Mass.
The following 2 users Like wrustle's post:
EdK (10-19-2013), Mayhem (10-19-2013)
#14
10-18-2013, 09:35 PM
As promised folks, here's the video.

Enjoy!!

http://youtu.be/1B206t17YM4

Best Regards,
Russ
Reply
Thanks given by:
LJP Offline
Sophmore
***
Posts: 75
Threads: 8
Joined: Aug 2013
Location: Medfield, MA
#15
10-19-2013, 06:04 AM
Looks nice Russ!
LJP, proud to be a member of MetalworkingFun Forum since Aug 2013.
Reply
Thanks given by:
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
#16
10-19-2013, 06:11 AM
Pretty slick Russ! Just curious, do they remaining pieces of alu. left on the chuck just go to the scrap bin?
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by: wrustle
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#17
10-19-2013, 06:32 AM
That is damn impressive Russ Thumbsup Smiley-signs107
I enjoyed the video Thumbsup
Smiley-eatdrink004
DaveH
Reply
Thanks given by: wrustle
wrustle Offline
Junior
****
Posts: 438
Threads: 67
Joined: Sep 2012
Location: Central Mass.
#18
10-19-2013, 07:05 AM
(10-19-2013, 06:11 AM)stevec Wrote: Pretty slick Russ! Just curious, do they remaining pieces of alu. left on the chuck just go to the scrap bin?

Yes sir, however, the batch of 400 of these (just slightly different) I am going to try to do three pieces in one handling to reduce the scrap.

Later,
Russ
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,739
Threads: 313
Joined: Feb 2012
Location: Arizona/Minnesota
#19
10-19-2013, 08:40 AM
Russ,

How do you remove the stub left over from the parting off operation?
Nice video, by the way. Thumbsup

Ed
Reply
Thanks given by: wrustle
wrustle Offline
Junior
****
Posts: 438
Threads: 67
Joined: Sep 2012
Location: Central Mass.
#20
10-19-2013, 08:46 AM
(10-19-2013, 08:40 AM)EdK Wrote: Russ,

How do you remove the stub left over from the parting off operation?
Nice video, by the way. Thumbsup

Ed

Hi Ed,

Thank you!

Typically we just clip it off with some wire cutters and then touch it up on a belt sander.

If the part requires a really good finish we then hit it on the scotch brite belt sander afterwards and it polishes it up super nice!

The total time from clipping to polish is about 15 seconds.

Best Regards,
Russ
Reply
Thanks given by: EdK




Users browsing this thread: 1 Guest(s)