Electronics Question (again...)
#11
(03-11-2016, 07:28 PM)Vinny Wrote: The light on the old one is a neon.  They run at 90v AC and the 33K resistor drops the line voltage to 90V.   The schematic for the knee feed looks like the light is also a neon.  

What I suggest is to find a neon panel lamp that's small enough to mount to the cover and wire it in without the resistor (the panel lamp will have the resistor built in).  Here's a link to some:

http://www.digikey.com/product-search/en...ageSize=25

EDIT:
Almost forgot, the reason the lamp looks to be wired right across the line is because the schematic is of the circuit board, the power switch is not mounted to it.

Vinny is correct that neon bulb is a game changer. 

Nice call Vinny  Thumbsup
Magazines have issues, everything else has problems

Reply
Thanks given by:
#12
(03-12-2016, 08:24 AM)pepi Wrote: that neon bulb is a game changer.

Not really, you can get LED pilot/panel lights that will run on 110/220VAC.

Ed
Reply
Thanks given by:
#13
Just out of interest - what is the issue with the lamp (big picture)? Is it that you finish machining a part and then find out three days later that you have left the unit switched on? If so, just kill the power to the machine after use. When I kill my power, the spindle motor, feed motor, coolant pump (not present yet) and the DRO all go off. Simple Big Grin
Hunting American dentists since 2015.
Reply
Thanks given by:
#14
(03-12-2016, 08:35 AM)EdK Wrote:
(03-12-2016, 08:24 AM)pepi Wrote: that neon bulb is a game changer.

Not really, you can get LED pilot/panel lights that will run on 110/220VAC.

Ed

But can you get them with the built in momentary push button switch in the center of the light ring? I searched Digi-key for hours trying to find one but couldn't. The only switches I could find with 110/120V illumination inputs were the neon lamped switches. Chin All the LED and incandescent versions were 12VDC.

That's why I just ordered a replacement switch for the knee feed to use on the table feed. Smiley-gen151
Willie
Reply
Thanks given by:
#15
(03-12-2016, 09:27 AM)Mayhem Wrote: Just out of interest - what is the issue with the lamp (big picture)?  Is it that you finish machining a part and then find out three days later that you have left the unit switched on?  If so, just kill the power to the machine after use.  When I kill my power, the spindle motor, feed motor, coolant pump (not present yet) and the DRO all go off.  Simple Big Grin

Close. Along with all the rest of the "accessories" on the same circuit is the SHOP LIGHTS. Even if I'm not using a machine and I'm working in the shop, I still need the lights! Leaving all the rest powered up all day long is pointless.
Willie
Reply
Thanks given by:
#16
(03-12-2016, 12:17 PM)Highpower Wrote: All the LED and incandescent versions were 12VDC.

A diode and resistor would make a 12VDC version work on 120VAC.

Ed
Reply
Thanks given by:
#17
(03-12-2016, 12:47 PM)Highpower Wrote: ...Along with all the rest of the "accessories" on the same circuit is the SHOP LIGHTS. Even if I'm not using a machine and I'm working in the shop, I still need the lights! Leaving all the rest powered up all day long is pointless.

That is why I ran a dedicated circuit to the mill and lathe. I can isolate each individually at their respective outlet or I can flick the circuit breaker and cut the feed to both.
Hunting American dentists since 2015.
Reply
Thanks given by:
#18
(03-12-2016, 08:35 AM)EdK Wrote:
(03-12-2016, 08:24 AM)pepi Wrote: that neon bulb is a game changer.

Not really, you can get LED pilot/panel lights that will run on 110/220VAC.

Ed

I would like to see a link and learn more about that. Surly it needs a bridge, can't think of it as a plug and play, or direct wire to line voltage. 

I am trying to fit this into the PF unit. The game changer comment was driven with the thought in mind that a circuit will need to in place to eliminate the neon, not a lot of unused real-estate  in there.

 I have also seen those bulbs used as a voltage regulator.  To be clear any observations or suggestion, I make require it to fit under the hood of that PF unit.

One other item, not real confident that those diagrams are complete. A quick scan did not see the speed control pot or variable resistor.
Magazines have issues, everything else has problems

Reply
Thanks given by:
#19
Chapter Two: A Fresh Start ... or is it?   Chin   Chin   Chin

Rotfl

Got the new switch in hand today to see what I could see....
First I checked the resistor that feeds the original neon lamp bulb at 32.97K? (Spec is 33K? 5%)

Then I attached a couple of jumper wires to the molex connector for the new ring light and applied them to the old neon lamp leads, and she lit up just fine.   Thumbsup

Now I just have to hope I guessed at ordering the correct mating connector and pins to connect the switch to.   Sweat
There are thousands of them.  Slaphead

   
Willie
Reply
Thanks given by:
#20
Smiley-eatdrink004
Magazines have issues, everything else has problems

Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)