How to Mill a Pocket on the Vertical Milling Machine
#11
a nuther good post
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
#12
Anybody else have the audio cut out on them when watching this video? It cuts out at about 1:30 and comes back at about 2:50 and then cuts out again at some point that I don't recall.

Ed
Reply
Thanks given by:
#13
(06-24-2012, 10:50 AM)EdAK Wrote: Anybody else have the audio cut out on them when watching this video? It cuts out at about 1:30 and comes back at about 2:50 and then cuts out again at some point that I don't recall.

Ed

Seems to be good from my end Ed. Have you checked the batteries in your hearing aid lately? Slaphead
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
#14
(06-24-2012, 10:50 AM)EdAK Wrote: Anybody else have the audio cut out on them when watching this video? It cuts out at about 1:30 and comes back at about 2:50 and then cuts out again at some point that I don't recall.

Ed

No, it is fine for me Ed, you must have gone deaf (temporally) Rotfl
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#15
(06-24-2012, 10:50 AM)EdAK Wrote: Anybody else have the audio cut out on them when watching this video? It cuts out at about 1:30 and comes back at about 2:50 and then cuts out again at some point that I don't recall.

Ed
Ed, if you think you're shabbily treated, all I got was this
"embedding disabled by request
Watch on YouTube
" .
I did route it through You Tube but when I saw it was 9+ mins.
I got impatient and gave up.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#16
Thanks Tom,Thumbsup

Very helpful! Smiley-eatdrink004

Jerry.Popcorn
ETC57, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
#17
(06-24-2012, 11:48 AM)TomG Wrote:
(06-24-2012, 10:50 AM)EdAK Wrote: Anybody else have the audio cut out on them when watching this video? It cuts out at about 1:30 and comes back at about 2:50 and then cuts out again at some point that I don't recall.

Ed

Seems to be good from my end Ed. Have you checked the batteries in your hearing aid lately? Slaphead

Ah, maybe that's it. I'll put some new batteries in and see if that helps. Big Grin

When I watched it I chose the highest resolution. I'll go back and watch it again but leave the resolutions on the default and see if I still have the problem.

Update: OK, the problem only appears if you select one of the HD resolutions, even with new batteries in the hearing aid. All other resolutions seem to play with no lose of audio.

Ed
Reply
Thanks given by:
#18
How about a vid on making a three eighths or half square recess in the end of a pin to turn with either a chuck key or a ratchet tom
Logan 10x26" lathe
SIEG 12x40" lathe
RongFU 45 clone mill
6" import band saw
Baldor Grinder
thousand of tools+tooling pieces 40 yrs of collecting
Reply
Thanks given by:
#19
(06-25-2012, 10:45 AM)TOM REED Wrote: How about a vid on making a three eighths or half square recess in the end of a pin to turn with either a chuck key or a ratchet tom

Hey Tom,

I think we can solve that problem without the need for a video. Why not just weld or solver solder a 3/8" or 1/2" drive socket to the end of the pin? If that doesn't float your boat, just mill a square pocket in the end of the pin and pick the radii out of the corners with a slotting tool like I did in my Steven's build thread.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
#20
http://www.homemodelenginemachinist.com/...pic=5495.0 This is the project I want to build and would like to make my own locking pins for the DI chuck 3 of them and would just like to be able to say I built the whole thing pins locks etc without welding, and a small radius in the corner of the pocket would be fine. tom
Logan 10x26" lathe
SIEG 12x40" lathe
RongFU 45 clone mill
6" import band saw
Baldor Grinder
thousand of tools+tooling pieces 40 yrs of collecting
Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)