MetalworkingFun Forum › Machining › General Metalworking Discussion v
Latest Delivery

Thread Modes
Latest Delivery
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
The following 1 user Likes Mayhem's post:
DaveH (04-17-2017)
#1,381
04-17-2017, 08:52 AM
Table turns when I crank the handle, so pretty good I think Big Grin
Hunting American dentists since 2015.
Reply
Thanks given by:
Vinny Offline
Another Whipping Boy
*******
Posts: 2,597
Threads: 99
Joined: Dec 2014
Location: Michigan
The following 4 users Like Vinny's post:
EdK (04-19-2017), f350ca (04-19-2017), Mayhem (04-20-2017), DaveH (04-24-2017)
#1,382
04-19-2017, 02:50 PM
I finally found one (actually he has several) and he was even really local! Well without further adieu, here it is:

[Image: press1.jpg]

[Image: press2.jpg]

The price wasn't too bad either.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Website
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,749
Threads: 314
Joined: Feb 2012
Location: Arizona/Minnesota
#1,383
04-19-2017, 03:16 PM
Nice find Vinny. Thumbsup

Ed
Reply
Thanks given by:
Dr Stan Offline
Senior
*****
Posts: 2,324
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
#1,384
04-19-2017, 03:57 PM
Those rotary tables can be v e r y dangerous.  Ship it to me and I'll check it out for free.   Big Grin
Reply
Thanks given by:
awemawson Offline
Junior
****
Posts: 642
Threads: 14
Joined: Oct 2013
Location: East Sussex, UK
#1,385
04-19-2017, 04:43 PM (This post was last modified: 04-19-2017, 04:44 PM by awemawson.)
Somebody stole the Fly from your fly-press !
Andrew Mawson, proud to be a member of MetalworkingFun Forum since Oct 2013.
Reply
Thanks given by:
Roadracer_Al Offline
Junior
****
Posts: 691
Threads: 14
Joined: Feb 2015
Location: Oakland, California
#1,386
04-19-2017, 05:11 PM
Fly press? Super awesome! I thought they usually had a bigger throat, though...
Reply
Thanks given by:
Vinny Offline
Another Whipping Boy
*******
Posts: 2,597
Threads: 99
Joined: Dec 2014
Location: Michigan
#1,387
04-19-2017, 07:19 PM
A fly press was just an idea/possible substitute for a kick press. The kick press is what I was really looking for. I pretty much gave up on the idea of a fly press when the only ones I could find around here were over $1000. This one was $230.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Website
Reply
Thanks given by:
Roadracer_Al Offline
Junior
****
Posts: 691
Threads: 14
Joined: Feb 2015
Location: Oakland, California
The following 1 user Likes Roadracer_Al's post:
pepi (04-26-2017)
#1,388
04-20-2017, 02:28 PM
Good price!
Reply
Thanks given by:
awemawson Offline
Junior
****
Posts: 642
Threads: 14
Joined: Oct 2013
Location: East Sussex, UK
#1,389
04-20-2017, 03:29 PM
Vinny, what sort of force can that kick press generate?

I have a corner notcher that works on the same principal, and doing more than one or two 2" corners gets old VERY quickly !
Andrew Mawson, proud to be a member of MetalworkingFun Forum since Oct 2013.
Reply
Thanks given by:
Vinny Offline
Another Whipping Boy
*******
Posts: 2,597
Threads: 99
Joined: Dec 2014
Location: Michigan
#1,390
04-20-2017, 04:46 PM
It has two positions for the motion and force. The position it's in now has less motion but more force. The spec for the short stroke is 2.5 tons. It's a Model 10. The specs are at the bottom of page 4: http://vintagemachinery.org/pubs/1416/6583.pdf
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Website
Reply
Thanks given by:




Users browsing this thread: 3 Guest(s)