I've been offered a surface grinder
#21
Thank you both.

I have contacted Chevalier and will wait to hear back. I read over on PM that someone else contacted Chevalier and the manual they sent was for a later version, which had ball bearing rollers for the table. However, looking at the image next to the manual Ed posted the link to, the table shows vee/flat ways.

Hopefully I will hear back from Chevalier today and if I have no joy, I will contact industrial manuals and ask if they can confirm the version they have. Thanks also for the offer Ed.
Hunting American dentists since 2015.
Reply
Thanks given by:
#22
Nice one Darren ,that be a canny addition to your shop , now you have two machines in bits  Big Grin , but still not as many as me  Slaphead



Rob 
Reply
Thanks given by:
#23
(11-25-2014, 07:37 AM)EdK Wrote: Here you go Darren.

http://www.industrialmanuals.com/chevali...p-3001.php

$39 for the hard-copy and $35 for the PDF or $56.50 for both...

I've always been a little sceptical of these sorts of sites, as many I see coming up in Google are just full of crap, spam and who knows what else.  I've also heard the horror stories of expensive manuals turning out to be very poor quality reproductions.

However, I must say how pleased I was that I bothered to contact them to ask if they could confirm if the manual covered the standard machine ways/rack and pinion version that I have.  Within a couple of hours of sending the email, I had this response from Adam:

"Here is a link to the manual.  If you like it just purchase on my site. If it doesn't work for your machine no charge."

I downloaded it at work and had a look and was very happy with the quality (scan of a 1970's manual) and the fact that it was indeed the correct one for my machine.  I immediately sent him an email, thanking him and I have just completed the PayPal transaction.

I find it refreshing that there are still people out there with enough trust to allow me to do this and so I really wanted to post it here, as I wouldn't hesitate to purchase another manual from him in the future.

(11-25-2014, 01:56 PM)RobWilson. Wrote: Nice one Darren ,that be a canny addition to your shop , now you have two machines in bits  Big Grin , but  still not as many as me  Slaphead

Rob 

Thanks Rob - if it makes you feel any better, I still haven;t finished my lathe (need to make parts for the feed system) and the motor and guards are still off of my shaper...
Hunting American dentists since 2015.
Reply
Thanks given by:
#24
Ken - are you still wanting a project for your dividing head?
Hunting American dentists since 2015.
Reply
Thanks given by:
#25
That's good news Darren. Thumbsup

Ed
Reply
Thanks given by:
#26
Thanks again Ed - I owe you one!
Hunting American dentists since 2015.
Reply
Thanks given by:
#27
(11-27-2014, 06:05 AM)Mayhem Wrote: Ken - are you still wanting a project for your dividing head?

Sure, why not! What would you have in mind?
Reply
Thanks given by: Mayhem
#28
(11-27-2014, 08:46 AM)Mayhem Wrote: Thanks again Ed - I owe you one!

You don't owe me anything. I'm happy to help.

Ed
Reply
Thanks given by: Mayhem
#29
(11-27-2014, 08:51 AM)PixMan Wrote: Sure, why not! What would you have in mind?

I'm going to need a graduated ring for the (missing) crossfeed handwheel. Now that I have a parts list, I looked these up on the US Chevalier website. The handwheel was $90.20 and the ring was $88.26 (out of stock).

I can make a handwheel.
Hunting American dentists since 2015.
Reply
Thanks given by:
#30
Darren, you can make the graduated ring too.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:




Users browsing this thread: 6 Guest(s)