Drawbar Wrench/Hammer
#1
Since the secret project is no longer secret I thought I'd start a thread on it.

An exploded assembly and a couple of pictures so far.

Ed

   

       
Reply
Thanks given by:
#2
Looking good Ed
I used copper on mine as brass tends to "spit" bits out
Not a good idea at eye level
John
Reply
Thanks given by: EdK
#3
(06-09-2013, 05:01 PM)doubleboost Wrote: Looking good Ed
I used copper on mine as brass tends to "spit" bits out
Not a good idea at eye level
John

Yikes

Maybe I should get a piece of copper. Thanks for the tip.

Ed
Reply
Thanks given by:
#4
(06-09-2013, 05:12 PM)EdK Wrote:
(06-09-2013, 05:01 PM)doubleboost Wrote: Looking good Ed
I used copper on mine as brass tends to "spit" bits out
Not a good idea at eye level
John

Yikes

Maybe I should get a piece of copper. Thanks for the tip.

Ed

I would Smiley-dancenanaSmiley-dancenanaSmiley-dancenanaSmiley-dancenana
John
Reply
Thanks given by:
#5
(06-09-2013, 05:15 PM)doubleboost Wrote:
(06-09-2013, 05:12 PM)EdK Wrote:
(06-09-2013, 05:01 PM)doubleboost Wrote: Looking good Ed
I used copper on mine as brass tends to "spit" bits out
Not a good idea at eye level
John

Yikes

Maybe I should get a piece of copper. Thanks for the tip.

Ed

I would Smiley-dancenanaSmiley-dancenanaSmiley-dancenanaSmiley-dancenana
John

I dunno I've had my Brass hammer for about 100yrs. and no problems.

   

I can still see pretty good out of one eye.

Blush
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#6
Well, there's really no clear lines between brass/copper/zinc alloys. There's a million of them.

I don't think I'll be able to use one of those. The Alliant mill has a long hex draw bar. While that allows you to change tools without fully retracting the quill, it means less clearance on top when you DO retract it.
Reply
Thanks given by:
#7
(06-09-2013, 04:56 PM)EdK Wrote: Since the secret project is no longer secret I thought I'd start a thread on it...

You should take that as a compliment Ed - you machining of one part was so good that I was able to figure out your top secret plan.
Hunting American dentists since 2015.
Reply
Thanks given by: EdK
#8
(06-10-2013, 07:16 AM)Mayhem Wrote:
(06-09-2013, 04:56 PM)EdK Wrote: Since the secret project is no longer secret I thought I'd start a thread on it...

You should take that as a compliment Ed - you machining of one part was so good that I was able to figure out your top secret plan.

Boy! I thought I could suck up. Smiley-dancenana
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#9
Just like the next guy, I don't mind a compliment every now and then. It helps to keep me motivated. Smile

Ed
Reply
Thanks given by:
#10
(06-10-2013, 07:04 AM)PixMan Wrote: Well, there's really no clear lines between brass/copper/zinc alloys. There's a million of them.
Yep, that's true Thumbsup
Smiley-eatdrink004
DaveH
Reply
Thanks given by:




Users browsing this thread: 2 Guest(s)