Press brake for 20 ton hydraulic press
#91
They look a little on the cool side Dave, the welding may say its at 95 but who knows, the current on the box is kind of like a speed limit sign, thats only a suggestion. Crank it up till you start to see some undercut at the edges of the weld, then drop back a bit, or leave it there and fill it in better. Unless your blowing through your good to go.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
#92
Thanks Greg,
I have to say it is not the first time it has been suggested my welds look a little cold.
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#93
Dave, yes you can try cranking it up a bit more and try that. You may end up getting a lot of spatter though. The thing is the type of flux on the 6010 rods allows your weld puddle to "dig" in better and get down into the root of your material more and wet out better. The flux on the 6013 rods is designed to prevent that, and keep it from burning through your material. It allows the puddle to cool faster and "freeze" the bead sooner which is a good thing for filling gaps.

6010 was designed to run on DC polarity, and later on they came up with 6011 that will run on AC polarity. Looking back now at your machine, it looks to be DC only.
Willie
Reply
Thanks given by:
#94
That's correct Willie, my machine is DC. I have tried it with the connections reversed - didn't make much difference to my welding Big Grin
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#95
The top die. This is 4" high x 16" long x .75" thick, and on one of the 16" long sides I have to machine a double chamfer 60 or 70deg (included) point.
   
Normally with long pieces I use two vices, however these two vices do not tilt. I have another vice that does tilt but only the one vice.
Anyone have an idea how I should do this?
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#96
Dave, do you by chance have an indexing head w/4 jaw chuck?

Or you could put your woodworking skills to use and build a v-block / fixture from lumber to hold the part at the proper angle and clamp the whole works to the table. Chin
Willie
Reply
Thanks given by:
#97
(06-20-2014, 10:57 AM)Highpower Wrote: Dave, do you by chance have an indexing head w/4 jaw chuck?

Or you could put your woodworking skills to use and build a v-block / fixture from lumber to hold the part at the proper angle and clamp the whole works to the table. Chin

I have an indexing head with a 4 jaw chuck. I was thinking about using the tilting vice one side and using a rotary table to hold the other end.
I didn't really want to make any fixtures - being the lazy bastard I am Big GrinBig GrinBig Grin
I'm just a bit concerned about the length and it flapping about in the breeze.

A couple of tilting tables would be nice Thumbsup which I haven't got Big Grin
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#98
I can hold it at a shallow angle or a steep angle. If I was using just the tilting vice I would tend to hold it at the steep angle and use the side of the end mill.
   

Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#99
(06-20-2014, 11:27 AM)DaveH Wrote: I have an indexing head with a 4 jaw chuck. I was thinking about using the tilting vice one side and using a rotary table to hold the other end.

I must have been reading your mind then. Big Grin

Just put some machinist jacks or blocks under the part to support it between your vice and indexing head.
Willie
Reply
Thanks given by:
Of course I could just use the tilting vice and "wing it" Big Grin May be if I roughly cut the 'V' out to start with and then just hold it with the tilting vice and take light cuts on the milling machine. Perhaps it's worth a shot Smile
It will either work or it won't.
Smiley-eatdrink004
DaveH
Reply
Thanks given by:




Users browsing this thread: 3 Guest(s)