MetalworkingFun Forum › Machining › General Metalworking Discussion v
Latest Delivery

Thread Modes
Latest Delivery
EdK Offline
Whipping Boy
*******
Posts: 8,749
Threads: 314
Joined: Feb 2012
Location: Arizona/Minnesota
#501
09-18-2015, 08:10 PM
Hmm, I'm not having any of those problems with mine. Although I've not used the full radius inserts yet. Probably because I don't think I have any. Big Grin

Ed
Reply
Thanks given by:
ieezitin Offline
Sophmore
***
Posts: 205
Threads: 27
Joined: Jan 2013
Location: Maryland USA
#502
09-19-2015, 06:19 AM
My Nikcole insert does not sit in line or parallel with the tool holder either, like you i was thinking it was a dud.

I have had a little trouble with chatter too but also success so my story is the same as yours. 

I am waiting to purchase the threading bits to try them out, i am waiting on a silly cheap post on fle-bays to snatch them up like i did last time on some parting off inserts, I robbed they guy by paying $2.00 each for ten.


Anthony.
ieezitin, proud to be a member of MetalworkingFun Forum since Jan 2013.
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,795
Threads: 183
Joined: Jun 2012
Location: Farmington Hills, Michigan
#503
09-19-2015, 08:33 AM
(09-18-2015, 06:43 AM)Mayhem Wrote: I spotted a Starrett S-828H centre finder set, which he was asking $25 for, which followed me home.

Nice find Darren.

We call them wigglers over here and they are nice, but not as accurate as the pin type edge finders. I use mine mostly for the point to pick up center punch marks or scribed lines, and for holding indicators.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
RobWilson
Unregistered
 
The following 1 user Likes RobWilson's post:
Mayhem (09-19-2015)
#504
09-19-2015, 11:06 AM
This lot arrived this week (the chemicals and beakers on the tray)  , mostly  for project X  Big Grin


[Image: P1090723_zpsfnukd2dr.jpg]

Still waiting for a few things to turn up  , the depleted Uranium must be stuck at customs Popcorn  

Rob
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,749
Threads: 314
Joined: Feb 2012
Location: Arizona/Minnesota
#505
09-19-2015, 11:32 AM
(09-19-2015, 11:06 AM)RobWilson. Wrote: ..., the depleted Uranium must be stuck at customs Popcorn  

Rob

Good one! Rotfl

Ed
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#506
09-19-2015, 11:45 AM
Good one Rob - that post will get the site on a FBI watch list and your address highlighted with major crimes division in the UK... I do hope that the chap with the rubber gloves is gentle Big Grin
Hunting American dentists since 2015.
Reply
Thanks given by:
RobWilson
Unregistered
 
#507
09-19-2015, 12:18 PM
The Lads at work have taken  to calling me Bomber Bob  Rotfl


Rob
Reply
Thanks given by:
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
#508
09-19-2015, 01:09 PM
looks like your fixing to maybe do some anodizing of aluminum
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,749
Threads: 314
Joined: Feb 2012
Location: Arizona/Minnesota
#509
09-19-2015, 01:15 PM
(09-19-2015, 01:09 PM)dallen Wrote: looks like your fixing to maybe do some anodizing of aluminum

That was my guess also until I saw this.

http://www.metalworkingfun.com/thread-72...l#pid48789

Ed
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,369
Threads: 178
Joined: Feb 2012
Location: Missouri, USA
The following 3 users Like Highpower's post:
EdK (09-19-2015), DaveH (09-19-2015), Mayhem (09-19-2015)
#510
09-19-2015, 05:13 PM
A couple more items scratched off of the "wish" list. Some recent flea-bay steals.

1/2" thick parallels.
Adjustable parallels.
Automatic drill drift.

Wavy parallels still enroute....   Smile 

   
Willie
Reply
Thanks given by:




Users browsing this thread: 6 Guest(s)