MetalworkingFun Forum
Making a steady rest - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: Making a steady rest (/thread-480.html)

Pages: 1 2 3 4 5 6 7 8 9


RE: Making a steady rest - doubleboost - 06-12-2012

Nice looking projectBig GrinBig GrinBig Grin
I am going to put roller bearings on mine
Watching with interestDrool
John


RE: Making a steady rest - f350ca - 06-12-2012

Nice work Mayhem. I've had roller and brass steadies and not sure which one I prefer. The surface has to be relatively smooth for either to work, you or at least I have to turn the surface if at all possible to get it round, its usually slightly oval or some odd shape. Once its smooth the brass runs nice with lots of oil. Cuttings don't bother the brass fingers, they get wiped away, where they just love to go under the rollers. The steady on my 18 inch lathe is heavy enough I have to use the crane to put it on, it has rollers and what I thought was a CHEAP plastic knob to hold the top half closed. Well that plastic knob makes a great relief valve. Was hogging some pretty heavy cuts close to the steady, one of the cuttings went under the roller and blew that knob to pieces. Not sure what would happen if it couldn't open, maybe twist the shaft between the chuck and the steady. Moral of the story, don't rule out the brass fingers, I've never had trouble with them.


RE: Making a steady rest - doubleboost - 06-12-2012

Greg
I will bear that in mind
John


RE: Making a steady rest - aametalmaster - 06-12-2012

Nice work. I have rollers on mine and ran one for 5 years at work with rollers...Bob


RE: Making a steady rest - doubleboost - 06-13-2012

(06-12-2012, 08:47 PM)aametalmaster Wrote: Nice work. I have rollers on mine and ran one for 5 years at work with rollers...Bob

Thanks Bob
The pictures have inspired me DroolDroolDrool
John


RE: Making a steady rest - Tony Wells - 06-14-2012

(06-12-2012, 05:20 PM)f350ca Wrote: Nice work Mayhem. I've had roller and brass steadies and not sure which one I prefer. The surface has to be relatively smooth for either to work, you or at least I have to turn the surface if at all possible to get it round, its usually slightly oval or some odd shape. Once its smooth the brass runs nice with lots of oil. Cuttings don't bother the brass fingers, they get wiped away, where they just love to go under the rollers. The steady on my 18 inch lathe is heavy enough I have to use the crane to put it on, it has rollers and what I thought was a CHEAP plastic knob to hold the top half closed. Well that plastic knob makes a great relief valve. Was hogging some pretty heavy cuts close to the steady, one of the cuttings went under the roller and blew that knob to pieces. Not sure what would happen if it couldn't open, maybe twist the shaft between the chuck and the steady. Moral of the story, don't rule out the brass fingers, I've never had trouble with them.


Having been around a great many roller based steady rests, I can tell you exactly what would have happened. Given the hp involved, the chip would have been rolled flatter, and the part would have suffered a scar shaped, oddly enough, just like the flattened chip. When I was in QC, I constantly rejected parts that were marred up from inattentive operators who let the chips build up around the rest until they were rolled in. On a finished OD, that required another operation to rework the diameter, provided the size would allow. That's another reason to keep the chips under control.
I prefer roller rests, and stick a barrier of some sort, like a plastic coffee can lid with a hole in it, just in front of the rollers. Works pretty well to keep the chips out.


RE: Making a steady rest - stevec - 06-14-2012

Tony, I hesitate to ask, but, is your real name Harold?
RotflRotflRotfl


RE: Making a steady rest - Tony Wells - 06-14-2012

^^^^^^^^^^^ Nope Steve, real name above.


RE: Making a steady rest - f350ca - 06-14-2012

Good one Steve
Tony good point, I use the coffee can lid trick all the time, but one heavy cutting managed (probably explainable by the Chaos theory) to get in the wrong place and bang. I have nothing against roller steadies, still use it, just saying there are options.


RE: Making a steady rest - Mayhem - 06-18-2012

OK, well seeing that Bill has joined us, I am going to ask for his help in detailing how to build telescopic fingers for my steady rest.

Bill has recently built one and did a fantastic job of detailing the build. He even posted a picture of the components and the order they go in. Unfortunately, I have been banned from the forum on which this was posted, so I can no longer go back and look at the pics and info.

Yes, I know I should have downloaded it but this way you all get to benefit too. See how I always think of you guys.