Setting Up My PM935 Mill
(02-22-2016, 06:22 AM)EdK Wrote:
(02-21-2016, 10:29 PM)Dr Stan Wrote: 1) what are you using as a hard point?

I'm not sure what you mean by "hard point".  17428

I'm not worried about getting it down the planks into the basement. Gravity is my friend. It's getting it off of the pallet and building a sled for it to anchor to. It can't lay on its side, it won't fit through the doorway.

Ed

A hard point is something one can attach to for heavy lifting, pulling, etc.  An example would be a large forged eye bolt embedded in  concrete.  I've used a leg of my welding bench since it is held firmly in place with 1/2" concrete anchors.
Reply
Thanks given by:
My "hard point" is a worm gear winch bolted to a 4x4 and braced across the door opening. So far it's worked fine.

Ed
Reply
Thanks given by:
The base casting is bolted to the pallet with four of these.

Ed

   
Reply
Thanks given by:
Can't get it off the pallet... Nothing to connect the chain to? How about removing the lag bolts, tilting it to insert lifting eyes in their place and put nuts on the bottom. Connect a chain or cable to each eye to your leveler and engine hoist. Yes? No?
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
(02-22-2016, 06:02 PM)Vinny Wrote: Can't get it off the pallet...  Nothing to connect the chain to?   How about removing the lag bolts, tilting it to insert lifting eyes in their place and put nuts on the bottom.  Connect a chain or cable to each eye to your leveler and engine hoist.  Yes? No?

I can get if off the pallet and I was thinking along those lines but I fear it may flip over on me. Sweat
I'd rather lift it from the top if possible. I'm considering putting the turret back on and lifting from it.

Ed
Reply
Thanks given by:
If you do it with the eyes on the base, when you lift it, as soon as the chains are tight you can strap the top to the 4 chains. It won't move then.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
(02-22-2016, 04:52 PM)EdK Wrote: My "hard point" is a worm gear winch bolted to a 4x4 and braced across the door opening. So far it's worked fine.

Ed

That's more than enough.   Thumbsup
Reply
Thanks given by: EdK
Not much to show but the sled is mostly done for the main casting. Now I've got to figure out how I'm going to get the casting onto the sled.  Chin

Ed

   
Reply
Thanks given by:
How about the crane you've been using for everything else?
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by:
(03-06-2016, 12:54 AM)Vinny Wrote: How about the crane you've been using for everything else?

Of course I'll use that. It's just that there's no real good way of grabbing on to the casting to lift it. I think I'm going to need to make use of the turret spider and some metal bar to rig up a lifting point. I'm still thinking about it. Chin

Ed
Reply
Thanks given by:




Users browsing this thread: 56 Guest(s)