Cheap Chinese Motor
#11
close enough for me seeing as how I measured mine with a cheap chinese micrometerSmiley-dancenanaSmiley-dancenanaSmiley-dancenanaRotfl
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
#12
most on here know that the motor on my mill burned up, after some thinking and soul searching I think it may of got a taste of lightening awhile back when both myself and the guy across the fence got hit, he lost a bunch of stuff up front, the day it happened I lost the HDMI port on my TV (no big deal) and the video card in my computer (Minor deal)

But I know from working on industrial stuff (asphalt plants) that some things don't show up for a while.

Anyway I received a motor that fit my mill, same dimensions motors actually physically bigger but from looking at name plates half a horse smaller then the burned up one. It came with a problem, the shaft is half and inch longer which makes it bottom out in the socket before the motor sits flat on the mill head. Now I could just stick some hacked out spacers under it, or leave the pair of 3/4 inch Parallels under it that are residing there now, but where's the fun in that SO I got out in the back yard yesterday and whipped up a spacer ring that I poured out of Aluminum.

heres some photos.
The Pattern
[Image: Spacer-Pattern.jpg]
Sand Prep
[Image: Sand-Prep.jpg]
just opened the mold
[Image: Casting-1.jpg]
out of the sand
[Image: Casting-2.jpg]
close up of Quarter that was put in for good luck
[Image: closeup-of-quarter.jpg]
part is in the lathe being cut now, have one side done will finish the other side this morning and hopefully get it put under the motor this afternoon.

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
#13
Nice work. I'd like to see some more pics/info of your muller.
Hunting American dentists since 2015.
Reply
Thanks given by:
#14
Good stuff DA Smiley-signs107
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#15
I wish I had the facilities to "whip up" castings. Big Grin

Nice job on the spacer, that should work well and you get to keep your parallels for holding other stuff up. Thumbsup

Ed
Reply
Thanks given by:
#16
(10-17-2012, 07:31 AM)Mayhem Wrote: Nice work. I'd like to see some more pics/info of your muller.

Mayhem I'll see about taking some shots of it and post them up to you. I based the muller off of one built by Steve Chastian, but I made a lot of changes to it in the drive as I didn't think I needed one as heavy as he built his. He got into actually casting a gear box case for his which I didn't see that I needed. Actually a right angle gear box of about a 40 to 1 ratio is pretty much the right speed. the drive shaft is pretty heavy I used a piece of 1 7/16" round bar to make mine out of.

here's the photos of the spacer ready to install under the motor as soon as a buddy of mine shows up to lend a hand to slide the spacer in when I pick the motor up.

[Image: Casting5.jpg]

[Image: Casting4.jpg]

and its installed
[Image: Casting6.jpg]
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
#17
I would have cut 3/4" 0ff the shaft.17428
But that wouldn't have been as much fun.Thumbsup
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#18
(10-17-2012, 01:19 PM)stevec Wrote: I would have cut 3/4" 0ff the shaft.17428
But that wouldn't have been as much fun.Thumbsup

Don't raise the bridge. Lower the river! Smiley-dancenana

A friends father told me years ago, what he saw in the service in WWII. A "carpenter" using a hatchet on the wooden floor of an office, because the door scraped... Chin
Reply
Thanks given by:
#19
That's a nice looking motor you have there David. Thumbsup
That spacer is not bad either. Big Grin

Ed
Reply
Thanks given by:
#20
So what happened to the quarter? 17428
Willie
Reply
Thanks given by:




Users browsing this thread: 2 Guest(s)