Making a Trap Stock for a Remington 870
#1
My has been taking an interest in trap shooting over the last couple of years but has been struggling because she has been borrowing guns that don't fit her very well (a common issue for women). This summer, we happened upon a 70's vintage Remington 870 for the right price, at an antique show of all places, and I bought it for her with the promise to get her measured for a proper trap stock and then make her one that would fit her perfectly. It was an ideal gun for her with a shorter 28" barrel, a modified choke and since it was an older, 1970's vintage, it was polished and blued, so it will make a nice looking trap gun. We had her shoot a try gun a few times this summer and worked out the best dimensions of the stock. The whole idea of fitting a trap gun is to make it shoot where you are looking with both eyes open without having to struggle to get your eye lined up on the bird. With all of the dimensions we came up with in hand and the wife out of town, I started off making the stock. I can't let Greg have all the fun working with wood.

The chunk of wood is a piece of fiddleback American walnut that I bought from a guy out in Washington (state). I've seen a lot of fiddleback, or curly maple, but walnut with this type of figure is sort of unusual. This particular piece came from a 7 foot diameter tree out in California. He sold me enough of the same pattern to make both the buttstock and the forestock.

The first task was to make a template from the measurements we took from the try gun. They were the length of pull which is the distance from the trigger to the center of the butt, the drop at the comb which is the distance from the top of the rib to the top of the cheek piece the drop at the heel which is the distance form the top of the rib to the top of the butt stock and the pitch which determines the angle of the buttstock against the shoulder. Whew! Sweat This will be a Monte Carlo stock, meaning that the comb is raised and parallel to the rib of the barrel. This reduces cheek slap from the recoil that you get with the angled comb on a field stock, a huge deal when you are taking 25 shots in a round of trap.

[Image: IMAG0372.jpg]

[Image: IMAG03733.jpg]

Next I rough sawed the shape and thickness leaving plenty of the pricey walnut to whittle away at.

[Image: IMAG037512.jpg]

Drilling the through hole for the mounting bolt took some thought, but I came up with the idea of locating and center drilling the hole location on the stock and using the lathe to drill it in from each end. Luckily, the two holes lined up perfectly in the middle.

[Image: IMAG0376.jpg]

My wife had her gun with her so I had to use one of mine as a pattern for the inletting. It was a fairly simple job on the mill using a tapered end mill and some freehand arcs (it's just wood).

[Image: IMAG0378.jpg]

[Image: IMAG0380.jpg]

Now that she's back in town I can start in on the final shaping using her gun as a guide. I'll post some more pics as the project progresses. The plan is to have it finished before our next trip up North at the end of the month. Hopefully she won't show me up once she has a properly fitted gun.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
#2
nice looking hunk of walnut


DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
#3
Hopefully it will retain the figure when I start shaping it. You never know for sure until its done. I did find a small void on the opposite side, but it shouldn't be too noticeable once it's filled.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
#4
Beautiful piece of wood Tom. Like the Hardinge drill press but can't quite figure out how your doing it. Sorry slow tonight (most nights)
Hope you show us the shaping.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
#5
Nice start Tom, Thumbsup
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#6
Nice work Tom. I have to really make sure I watch my manners next time I drop in if Marty is going to be armed!
Hunting American dentists since 2015.
Reply
Thanks given by:
#7
(09-09-2014, 12:38 AM)f350ca Wrote: Like the Hardinge drill press but can't quite figure out how your doing it. Sorry slow tonight (most nights)
Hope you show us the shaping.

I just located and center drilled the hole on each end and drilled as far in as possible in each end with a drill in the spindle and a center in the tailstock for alignment.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
#8
(09-09-2014, 06:31 AM)Mayhem Wrote: Nice work Tom. I have to really make sure I watch my manners next time I drop in if Marty is going to be armed!

Armed or not Darren, she is one tough cookie. Happyyes
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
#9
hi brill i love the type of wood you is using [/b]
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
#10
Very nice lump of timber
Your machines are now "contaminated" YikesYikesYikesJawdropJawdropJawdrop
John
Reply
Thanks given by:




Users browsing this thread: 3 Guest(s)