Declaring victory! 4x6 bandsaw refitting project
#1
I've had a Harbor Freight 4x6 bandsaw for close to if not more than 25 years. (Jeez, I feel old just saying that!) Like most HF tools, it was a kit delivered in assembled form. It required a lot of tinkering to make it cut straight and not throw the blade. After tinkering and tuning, it worked acceptably well for many years.

Recently, however, it started throwing blades again, to the point of frustration: yesterday, I was shopping for a new 7x12 saw. (I was considering either the TurnPro from ENCO, or the Balleigh, which is a Taiwanese product. What I **really** want is an Ellis with mitering, but it's too big, and it's expensive.)

None of the usual tuning tricks helped, so I looked into the workings and found that a number of bits & pieces had worn quite badly. In part, because I never thought of it as requiring maintenance, and in part due to poor workmanship or poor design. I also decided to fix a couple of crappy production details.

Paying work was slow today, so I dove in. Here's what I found:

1) lower/driven wheel - drive surface had worn to a cone shape, this was the primary cause of throwing blades. The wheels for this type of bandsaw are cast iron, with a flange on the back edge, and no rubber tire. The diameter of the front edge of the wheel was .07" smaller!!

2) the drive shaft & drive wheel would move axially about .0625"

3) upper wheel bushing was thoroughly clapped out and wobbly on the shaft.

4) upper wheel was also cone-shaped, but less so - about .03".

5) the upper wheel retaining arrangement had become sloppy - there was probably close to .1" axial slop.

6) the tracking adjustment had become loose, and was rocking side to side considerably.

7) the blade guides have always needed a quick pass under the mill spindle to sit flat in the saw chassis and remove a slight twist in the blade due to the as-cast surface of the blade guides.

I tackled the easiest job first: the blade guides were removed, clamped in the mill vise, and cleaned up, successfully removing the twist in the blade. The nasty funk buildup on the guide rollers was removed in the parts washer, and re-set to the correct width.

The next job was to fix the lower wheel. A bit of cursing, prying, and beating removed the lower wheel without breaking anything or resorting to heat. I put a big chunk of hot roll in the Victor and whipped up a 15mm diameter mandrel to mount the lower wheel on. I threaded the end and captured the wheel on the mandrel with a 10x1.25 bolt and heavy washer. In addition to the cone-shaped wear, there was a small amount of runout on both the flange and diameter. Both were corrected with light cuts.

One of the real joys of Mainland Chinese Industrial Design is a complete disregard for servicing. One indicator of this is that the drive shaft is located only by the worm gear inside the gearbox. When you try to slide the lower wheel onto the shaft, it retreats into the gearbox, forcing you to either drain the gearbox or balance it on it's left side, in order to keep the gear oil in the open gearbox. To get the right amount of axial play, the drive wheel & shaft have to be pushed together from the gearbox side. Just as a belt and suspenders approach to eliminating the axial play, a washer of the correct thickness was modified to fit between the drive wheel and circlip on the drive shaft.

The bushing in the top wheel was pressed out, a new bronze bushing turned on the lathe, and pressed into place. It was then mounted on the same mandrel (returned to the lathe in a 4-jaw and dialed in to zero-zero). The top wheel was quite a mess: the flange had about .06" of runout, and the wheel had some significant radial runout - I didn't measure, but it was visible. Cuts were made to true up the flange and wheel, but also to reduce the thickness of the wheel by the amount taken off of the flange. The last item is important because the teeth of the blade have "set" - they're proud of the band - and if they run on a metal wheel, it will beat the set out of the blade, causing curved cuts.

Bronze washers were made up to bring the top wheel into alignment with the bottom wheel. Alignment was checked with a piece of square tubing clamped to the lower wheel.

Tracking was initially set for the upper wheel to be parallel to the lower wheel, and adjusted so the blade lightly touches the back flange. All the tracking fasteners were then tightened. I may add some blue loctite to prevent them from loosening in service.

Proof of the pudding is in the sawing, and it happily sliced through some 2" .032 wall stainless tubing - something which had given it fits previously.

Victory was declared! All in all, a very satisfying day in the shop! Best of all, I didn't spend $1600 on a new saw!
Reply
Thanks given by:
#2
Congratulations, well done.

When I read about things like this I'm so grateful that my dad had spent a little more on the MSC-branded Taiwanese 7x12 saw. I haven't had to do a thing to it.

Yesterday I managed to disregard all other responsibilities and get into the shop, that say played a big part in activities with my son's project of making a custom changeable counterweight setup for his RC car. he used the saw for lopping off bar stock for the aluminum brackets, then cutting up the brass for the weights (little plates.)

That saw cost my dad about $695 perhaps 8 years ago. I think it would be labeled as the TurnPro one now.
Reply
Thanks given by:
#3
Yes, that would be it. They're up to a bit over $1000 now. They seem to be well-respected, unlike some of the lower-grade Mainland China saws.

When I got out of roadracing motorcycles, I had a deep need for some kind of competitive activity, so I took up 1/10 scale electric touring car racing. I didn't last long: track-driving had a steep learning curve, and I got tired of having my a$$ handed to me by 12 year olds. ;) I still have the car somewhere, I should dig it out and buy some new packs for it. I had probably the last NiCad packs ever sold -- seems like the industry has gone to LiPo packs.
Reply
Thanks given by:
#4
Sounds like you've given it a thorough overhaul.
I've had a 7 x 9 for probably 5 or 6 years now. Pretty sure its of Chinese heritage, came from Princess Auto. Hasn't given me a bit of trouble, cuts straight till the blade is worn to the point of wearing through stock. Only maintenance it ever got is degreased and pressure washed every couple of years, boy they get gross with the water soluble coolant.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
#5
Am I the only one who is going to say without pictures...

Sounds like your hard work paid off. Mine is on my list of equipment that needs some TLC.
Hunting American dentists since 2015.
Reply
Thanks given by:
#6
Those 4x6 band saws are brilliant little machines I know most are made in China but change the saw blade to a decent one and you are off.
For the price you can't go wrong.
25 years .......... isn't bad Smile 
Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
#7
RR Al,
Several years ago I had to "service my 4x6, many similar problems as yours.
I had to replace the bronze worm wheel as well.
I sourced worm gear from Union Gear, Quincy Mass. # BWG-1220-SR and the bearing is a 6202ZZ NR/2A.
I also had to machine off the remains of the edge on the rear of the drive wheel and replace it.
Still going strong.

Steve

Smiley-eatdrink004
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#8
I bought my Enco 5x6 band saw back when they were still made in Taiwan and I haven't done anything to it other than replacing the factory supplied blade with a bimetal blade. I used the original blade to saw a bunch of rectangular tubing until it got dull and then switched over to the bimetal blade.

Ed
Reply
Thanks given by:
#9
Yes, indeed -- they are real workhorses once you get them working correctly. But the fixing up process... well, it made me wonder if I'd made a bad decision.

During yesterday's process, I wasn't sure if my efforts would yield acceptable results, so I didn't bother with photos. I have to take the top wheel off to chamfer the edge (forgot a step), so I'll take photos of what was done there.

I was shocked at the conical wear on the drive wheel. Hell, I'm shocked that I fixed it so easily.

@SteveC - thanks for those part numbers, they'll probably come in very handy someday! The 4x6 doesn't seem to have the same gear wear problems common in the 7x12 saws. I read several reports of multiple gear failures and subsequent abandonment of tool. I think neither are industrial grade tools.
Reply
Thanks given by:




Users browsing this thread: 2 Guest(s)