Floor mats
#1
So I am standing in front of the mill (on concrete) and realize that I need to buy a mat to ease my aching joints. Of course, I come here to get some experienced opinions on which mats work best and what size do you recommend. I found a likely mat at Costco in both 2' x 3' and 3' x 5' sizes and think the 2'x3' might be the one to get but there is a local company in my area that makes the same mat to any size you want at basically the same cost per foot. What do you guys think? Here's the link to costco.

http://www.costco.com/Browse/Product.asp...opnav=&s=1
Collecting tools for 30 years.
Reply
Thanks given by:
#2
Lowes sells them for about 15 bucks a pop. 3' x 4', I think. I bought a bunch, and on areas I stand a lot (in front of the workbench) I doubled them up for extra comfort.
Full of ideas, but slow to produce parts
Reply
Thanks given by:
#3
I'm working on an adaptation of this

.jpg   528_loveseat[1].jpg (Size: 12.58 KB / Downloads: 157) .
My problem is to get casters that won't bung up with swarf.
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#4
I use these.

http://www.menards.com/main/flooring/uti...126534.htm

One side is colored, the other side is gray.

http://www.norsk-stor.com/24.html

Ed
Reply
Thanks given by:
#5
I'm gonna look into that Ed. How do you think the lazy boy's casters will handle that?
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
#6
I made a sandwich: 3/8" plywood on the bottom, a Sears workshop mat in the middle, and 1/4" plywood on top. This prevents swarf from becoming embedded in the mat.


Actually I simplified a bit. As both my lathe and mill are mounted on 4x4 timbers, I could afford to place 4 1x3 strips (strapping) under the sandwich, giving additional yield and spring to the upper surface (at the cost of 3/4" rise in height). The sandwich is screwed into the strips, holding the whole assembly together.


It's comfy and works for me ...
Reply
Thanks given by:
#7
(06-14-2012, 06:26 PM)stevec Wrote: I'm gonna look into that Ed. How do you think the lazy boy's casters will handle that?

Steve,

The Lazy Boy casters would probably not be good for that matting. Change to some larger diameter casters and you should be good to go. Big Grin

Ed
Reply
Thanks given by:
#8
(06-14-2012, 05:38 PM)EdAK Wrote: I use these.

http://www.menards.com/main/flooring/uti...126534.htm

One side is colored, the other side is gray.

http://www.norsk-stor.com/24.html

Ed

Ed,

I use the same mat tiles but one thing I don't like is the lathe swarf sometimes sticks into the mat. Seems like there must be mat that is just cushioned enough to be comfortable but not so soft it picks up swarf.

Henry Arnold
henryarnold, proud to be a member of MetalworkingFun Forum since Apr 2012.
Reply
Thanks given by:
#9
Mine is about 4x6' one inch thick the kind with one inch holes. The holes catch swarf,
nice on my feet and as for dropping say a nut (that always dissapears) it will catch
that too. Somebody gave it to me long ago. Just pick it up and sweep. Its a catch all.
big job, proud to be a member of MetalworkingFun since Jun 2012.
Reply
Thanks given by:
#10
(06-14-2012, 10:49 PM)henryarnold Wrote:
(06-14-2012, 05:38 PM)EdAK Wrote: I use these.

http://www.menards.com/main/flooring/uti...126534.htm

One side is colored, the other side is gray.

http://www.norsk-stor.com/24.html

Ed

Ed,

I use the same mat tiles but one thing I don't like is the lathe swarf sometimes sticks into the mat. Seems like there must be mat that is just cushioned enough to be comfortable but not so soft it picks up swarf.

Henry Arnold

Henry,

Yup, the swarf does tend to stick to the matting if it's hot but it doesn't bother me. I just pick it out with a needle nose pliers when I clean up. I like that matting because I'm small and a lot of the anti fatigue mats are made from too hard of a material for my weight so they don't cushion my feet much. The foam matting works great for me.

Ed
Reply
Thanks given by:




Users browsing this thread: 2 Guest(s)