Mill Engine Cylinder Casting
#21
More displacement equals more torque. Thumbsup

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
#22
With a slightly larger bore and the same stroke you may (in my very limited understanding) be able to turn higher RPM. I wish I could see all the pictures. I think I will try my hand at some of this casting. I want to make a small running engine to put in a R/C model. Probably not a scale Chevy 350 or 351 Windsor or anything but something out of the ordinary. I definitely look forward to checking this out thoroughly when I'm home and have unrestricted internet!!
SnailPowered, proud to be a member of MetalworkingFun since Aug 2012.
Reply
Thanks given by:
#23
(08-20-2012, 06:11 PM)TomG Wrote: More displacement equals more torque. Thumbsup

Tom

Or as the saying goes, "there is no substitute for cubic inches"
Hunting American dentists since 2015.
Reply
Thanks given by:
#24
(08-21-2012, 07:19 AM)Mayhem Wrote:
(08-20-2012, 06:11 PM)TomG Wrote: More displacement equals more torque. Thumbsup

Tom

Or as the saying goes, "there is no substitute for cubic inches"

BAH Humbug! Rotfl Boost is definitely a replacement for displacement. Look at the new Ford Eco-boost. I'm not a Ford fan at all but I WANT that truck!! Thumbsup
SnailPowered, proud to be a member of MetalworkingFun since Aug 2012.
Reply
Thanks given by:
#25
(08-21-2012, 10:49 AM)SnailPowered Wrote: BAH Humbug! Rotfl Boost is definitely a replacement for displacement. Look at the new Ford Eco-boost. I'm not a Ford fan at all but I WANT that truck!! Thumbsup

Don't do it.

PM me and I'll fill you in on my recent experience with Ford products.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
#26
any progress on the steam engine
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
#27
(09-15-2012, 08:18 AM)dallen Wrote: any progress on the steam engine

Hi
I need to cast another cylinder (not happy with that one)
I have my mill in bits now (Z screw nut is nearly stripped)
To many jobs not enough time
John
Reply
Thanks given by:
#28
(09-15-2012, 11:17 AM)doubleboost Wrote:
(09-15-2012, 08:18 AM)dallen Wrote: any progress on the steam engine

Hi
I need to cast another cylinder (not happy with that one)
I have my mill in bits now (Z screw nut is nearly stripped)
To many jobs not enough time
John
Hi John,

Well that is a bit sad, casting a new one but if you're not happy it's the only way to go.
However it is good for MetalworkingFun we get a casting video, don't we please Worthy
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
#29
sorry about the Z Axis nut, was just wondering hadn't seen anything posted for a while on it and I really want to see this engine finished, I hope to do a steam engine one day. I want one that I can actually use.

As far as casting goes I fired my furnace up today after about 4 months of the state being under a burn ban, sorry no video. poured a new rammer that I think is going to be way too heavy.
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:




Users browsing this thread: 2 Guest(s)