Todays Project - What did you do today?
Greg,

The possibilities for wood like that are endless. When you bookmatch a couple of boards like that, do you cut the log down the center first and then take the board on each side? How are you going to cut the rest? Most ash I've seen was just plain sawn.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
Tom, we're still in he learning mode as far as being a sawer is concerned. This is the first quarter sawing I've done so played it a little cautious. Was afraid the exact middle of the log might have some funny things going on so I cut 3 boards out of the center, one above, one with the pilth in the middle of the board and one below. The center board is true quarter sawn, the ones on either side are so close on a log this large that for all intensive purposes they are quarter sawn. This gave me 2 choices for book matching. Quarter sawing yields more stable lumber, a lot less likely to cup. Important for table tops and I'm hoping for boards this wide. The rest of the log is close to quarter sawn.
I took one of the remaining cants stood it on edge the cut one board above and one below center. Again if I'd taken one out of the center it would be true quarter sawn but one on each side is real close. Now the two cants from this were sawn. I set the saw to cut one inch boards above the bunks, put the cant on the bunks and cut a board, remove board and flip the cant 90 deg, cut a board and repeat till your boards are down to say 3 inches. The further out from center you get the more radial or flat sawn the boards are but still beter than actual flat sawn.
Lets hope a picture is worth a thousand words or about 10 thousand of mine.

[Image: IMG_0241.jpg]

Most lumber even oak now is plain sawn just because of the time it takes to quarter saw I guess, but here time isn't worth much.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
Thanks for the in depth explanation Greg (even a pic!).

I can definitely see where the best quarter sawn boards are those closest to the center of the log. I believe the best wood is obtained by rift sawing, where the boards are cut radially from the log. That way the grain is perpendicular to the surface on all boards. Unfortunately that technique also produces the most waste.

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
Finished up sawing that log, The scale chart said it should yield 170 board feet. Rough measured showed 172 in the pile.

[Image: IMG_0243.jpg]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
Greg,

How thick did you cut the boards? Looks like about 1" or so.

Ed
Reply
Thanks given by:
The three center boards are 5/4, thought I might want the extra for table tops, the rest is inch.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by: EdK
I finished off a project today Thumbsup (nearly I think Rotfl )

Made from some engineering plastic - I have no idea what - too long ago. Part of something I started to make in 1998 Popcorn

So ............ I'm a bit slow Rotfl

   

   

   


Pretty good eh! RotflRotflRotfl
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
Good looking part Dave.

It looks like Delrin or some other brand of acetal. I assume it's a handle for a machine crank? You should try buffing it to make it shine. Shiny is always better! Thumbsup

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
(10-10-2012, 08:50 AM)TomG Wrote: Good looking part Dave.

It looks like Delrin or some other brand of acetal. I assume it's a handle for a machine crank? You should try buffing it to make it shine. Shiny is always better! Thumbsup

Tom
Thanks Tom,
Buff it Chin Ok I might give it a goThumbsup
And you are right it is a handle for a crank Thumbsup You're just clever like me RotflRotflRotfl

Smiley-eatdrink004
DaveH
Reply
Thanks given by:
Hi Tom,
Gave it a bit of a buff, didn't really make it shiny Chin
Any suggestion for the type of best buffing compound to make it shine?
Smiley-eatdrink004
DaveH
Reply
Thanks given by:




Users browsing this thread: 29 Guest(s)