Todays Project - What did you do today?
(05-11-2013, 10:27 PM)dallen Wrote: took all the screws out of this and watched it fall apart in my hands

Now you can have some fun, but mind those springs they is nasty things.

Brian.
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
I broke my friend's lathe, so I had to fix it!

I was using it to turn a 60* point to chuck into my drill press to aid in aligning a tap. Simple 10 minute job...

I turned and faced a suitable piece of small diameter round stock and then set the compound to 30* and tightened the nuts. I just nipped them up with the tiny wrench they supply but I still managed to strip the threads on one of the T-bolts. OK I thought - I should still be able to take light cuts with just one of the two done up. Yep - you guessed it - there goes the other thread Slaphead

I cut the offending threads off and filed the bases flat. Found a couple of suitable M6x1 bolts to use and cut them to length. I then drilled and tapped the bases and staked the threads, so they wouldn't come loose. I wonder if he will know?

Original T-bolt above the donor thread and base:
   

Finished repair:
   

Back in action:
   
Hunting American dentists since 2015.
Reply
Thanks given by:
If he doesn't know he won't appreciate the improvement you've performed. Rotfl

I've always tried to return a borrowed tool or device either improved or in better condition than it was when I borrowed it.
Thumbsup
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
(05-12-2013, 06:19 AM)stevec Wrote: I've always tried to return a borrowed tool or device either improved or in better condition than it was when I borrowed it.
Thumbsup

I do the same as that's what my parents taught me to do.

Although it's usually people borrowing tools from me. I remember borrowing a hammer drill from my brother about 8 years ago but that's about it.

Ed
Reply
Thanks given by:
(05-12-2013, 02:03 AM)Brian Wrote:
(05-11-2013, 10:27 PM)dallen Wrote: took all the screws out of this and watched it fall apart in my hands

Now you can have some fun, but mind those springs they is nasty things.

Brian.

its has only one spring in it and I don't have a clamp ring so I guess I'll make a couple of those today. I figured out where everything goes and got it all back together last night but having a heck of a time figuring out how the part that the hammer is on fits into it. this is a junk movement I got off EBay to mess with and someone treated it really bad, plates are bent some and will either have to be straightened or if I feel lucky new ones made, plus some of the pivot holes are loose.

Whats the best way to polish the wheels besides carefully???

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
did this yesterday, Idler Roller for a belt sander that I hope to put together to use 2 inch wide belts.

   
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
(05-12-2013, 09:24 AM)dallen Wrote: Whats the best way to polish the wheels besides carefully???

DA

Do you have an ultrasonic cleaner?

http://timesavers.com/i-9500943-historic...-pint.html

They'll come out shining like a new penny.
I polish pivots with a burnishing tool...
Willie
Reply
Thanks given by:
made this puller

   

to remove this gear from the clock movement that I showed in a previous post

   
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
boiled it in some niter salts after doing a little clean up on it. also change the screw to one more suitable for the application

   
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
Nice! It looks like a proper tool now.

Ed
Reply
Thanks given by:




Users browsing this thread: 37 Guest(s)