Latest Delivery
Tom - I believe that Ed has reached the age or dry dreams and wet farts Big Grin
Hunting American dentists since 2015.
Reply
Thanks given by:
(11-26-2013, 09:26 PM)Mayhem Wrote: You can't just post a picture of the box Ed

Let me help you out with that then. Big Grin

It would look like this one that the red arrow is pointing at. Just a few more to go Ed, and you'll be able to tap just about anything, any size up to 3/4"/20mm threads. Beyond that, single point 'em!

[Image: IMG_0744-r3.jpg]
Reply
Thanks given by: EdK
(11-27-2013, 08:53 AM)Mayhem Wrote: Tom - I believe that Ed has reached the age or dry dreams and wet farts Big Grin

Oops, did I leave the web cam on last night. Yikes

Ed (I think 17428)
Reply
Thanks given by:
Here's my version of what Ken already showed you. Big Grin

Ed

   
Reply
Thanks given by:
OK Ed, can't let you get all the goodies.

Here is the latest I picked up for use with the presses.

Mueller Kueps Press and Pull Sleeve kit. # 609400

44 mm (38 mm) x 34 mm up to 82 mm (76 mm) x 72 mm in steps of 2 mm and 55 mm long. One end has an internal step the ( dimension ) in one end so they can be stacked and nested togther. Tie bolts with thrust bearing nuts and stepped end plates.

   

   

This set overlaps slightly but basicly steps up from where my other set left off, shown in this picture of my friends set on its original wooden stand. Mine is stored in the door shelves if my wall cabinets.


.jpg   Bearing Press sleeves.jpg (Size: 19.73 KB / Downloads: 162)

This set is from 9.55 mm x 6.15 mm to 49.26 mm x 42.86 mm in both 38 and 101.5 mm long.

   

   

Walter
starlight_tools, proud to be a member of Metalworking Forum since Apr 2012.
Reply
Thanks given by:
My latest acquisition showed up today (the lady who delivers our mail was not happy Blush)...

Ellis dividing head:

[Image: ellis01.JPG]

[Image: ellis02.JPG]

Now it's slated for a session in the Evapo-rust, general clean up, and lubrication.

-Ron
11" South Bend lathe - Wells-Index 860C mill - 16" Queen City Shaper
Reply
Thanks given by:
Ron

Nice dividing head

I got a Vertex 9" a month back. Was supposed to be B&S #9 but was MT3 and the spindle was supposed to be 1-1/2x8 threaded with the primary index plate seerate from the chuck plate, but now they are combined.. GRRRR.

   

So it will work, but more trouble to change chucks etc if needed.

Walter
starlight_tools, proud to be a member of Metalworking Forum since Apr 2012.
Reply
Thanks given by:
Ordered this yesterday.
VFD
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
Got these dies today. They are made in China but at least they are some version of HSS, at least they claim to be. I checked the price on the better ones and they were way over my budget. If these don't work out, I'll just buy good ones as I need them rather than drain the bank account all at once.

Ed

   
Reply
Thanks given by:
Look alright from here Ed, ............ I'm sure they will be fine Thumbsup
Smiley-eatdrink004
DaveH
Reply
Thanks given by: EdK




Users browsing this thread: 13 Guest(s)