Todays Project - What did you do today?
(01-02-2016, 11:42 PM)Highpower Wrote: According to my highly calibrated Japanese hardness testing files  Rotfl I'm estimating about 53 - 54 HRC after the tempering.

Maybe a tad towards the high side, but I'd say that was just about right.  It's not seeing a lot of impact/shock type force, so it should hold up quite well.
Full of ideas, but slow to produce parts
Reply
Thanks given by:
(01-02-2016, 07:17 PM)Mayhem Wrote: Nice work Johnny - you may want to place a length of stock into the left-hand side of the vice to even things out when you have the pallet mounted over on the right-hand side.

(01-02-2016, 07:56 PM)TomG Wrote: You should also throw a clamp on the supported end of the pallet. It wouldn't take much to lift it off the jacks.

Thanks for sharing your set-up.

Tom

Both good point guys, thanks.

John
johnncyc14, proud to be a member of MetalworkingFun Forum since Nov 2013.
Reply
Thanks given by:
(01-03-2016, 02:45 PM)rleete Wrote:
(01-02-2016, 11:42 PM)Highpower Wrote: According to my highly calibrated Japanese hardness testing files  Rotfl I'm estimating about 53 - 54 HRC after the tempering.

.....  It's not seeing a lot of impact/shock type force, so it should hold up quite well.

I don't know.... you haven't seen me hanging from the bar and bouncing up and down trying to free a bearing from a motor armature. Rotfl

The more I think about it, the more I want to go ahead and do a second tempering and bring the hardness down some more. The areas around the keyway corners are pretty thin. Chin
Willie
Reply
Thanks given by:
Today I swapped the 240v single-phase in, 240v 3-phase out VFD on my lathe for a 415v 3phase in, 415v 3-phase out model. It was only a few months ago that I cottoned on to the fact that I was running a 415v 3-phase motor on a 240v 3-phase supply, which explained why it would not run up to speed in top gear, and why it slowed down with heavy cuts. Since I now have 415v 3-phase available via my rotary phase converter, I decided to feed the lathe the volts it requires, spotted an appropriate VFD on eBay for a reasonable price and it has been sitting in the shed for a couple of months. I ran out of time tonight before I could chuck anything up and make some thick chips, but the lathe now runs up to full speed without difficulty. As an added bonus, I discovered that the chart on the gearbox is not quite correct, all the other gears clock exactly as charted including 4th with 700rpm in high, but what is marked as 3rd (of 4) gears with 400rpm actually gives me a tad over 1100rpm in high range. Happy days.
Lathe (n); a machine tool used in the production of milling machine components.

Milling Machine (n); a machine tool used in the production of lathe components.
Reply
Thanks given by:
(01-04-2016, 06:00 AM)Pete O Wrote: Happy days.

Good to hear Pete. Thumbsup
Willie
Reply
Thanks given by:
The staircase wouldn't fit into the basement assembled so today Charlie gave me a hand to put it together on location, instal is scheduled for tomorrow.
He set up a camera and did a 30 second per shot time lapse.
Wish I could actually work that fast.

https://www.youtube.com/watch?v=IXnMxMYiPYw
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
Brilliant Greg Thumbsup 
Smiley-eatdrink004 
DaveH
 a child of the 60's and 50's and a bit of the 40's Smile
Reply
Thanks given by: f350ca
Yeah, you guys sure do work fast!
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Reply
Thanks given by: f350ca
(01-04-2016, 07:44 PM)f350ca Wrote: Wish I could actually work that fast.

https://www.youtube.com/watch?v=IXnMxMYiPYw

Greg with the amount of progress you seem to make on a multitude of projects, I thought that was how things must look in your shop on a normal day.
Lathe (n); a machine tool used in the production of milling machine components.

Milling Machine (n); a machine tool used in the production of lathe components.
Reply
Thanks given by:
(01-06-2016, 02:03 AM)Pete O Wrote:
(01-04-2016, 07:44 PM)f350ca Wrote: Wish I could actually work that fast.

https://www.youtube.com/watch?v=IXnMxMYiPYw

Greg with the amount of progress you seem to make on a multitude of projects, I thought that was how things must look in your shop on a normal day.

I assumed the vision was played back at slow speed...
Hunting American dentists since 2015.
Reply
Thanks given by:




Users browsing this thread: 23 Guest(s)