MetalworkingFun Forum › Machining › Projects v
Todays Project - What did you do today?

Thread Modes
Todays Project - What did you do today?
EdK Offline
Whipping Boy
*******
Posts: 8,741
Threads: 313
Joined: Feb 2012
Location: Arizona/Minnesota
#2,351
09-03-2014, 03:39 PM
Very nice Steve. Thumbsup

Ed
Reply
Thanks given by:
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
The following 2 users Like dallen's post:
EdK (09-04-2014), oldgoaly (09-05-2014)
#2,352
09-04-2014, 10:37 AM
been out in the back yard playing with the furnace again.

looks pretty good from this side
   

not so good from this side
   

but I know how to fix it, should of put a riser on the hub to feed back into the part when it cooled off, NiBrAl shrinks really bad in some castings.

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
tackit Offline
Sophmore
***
Posts: 125
Threads: 18
Joined: May 2014
Location: IN
#2,353
09-04-2014, 09:08 PM
(09-03-2014, 02:07 PM)schor Wrote: Made a couple bedroom door signs for my daughters out of some nice birdseye maple I had.

[Image: IMG_20140903_143627.jpg]

[Image: IMG_20140903_143613.jpg]

[Image: IMG_20140903_143603.jpg]

Those are beautiful schor, I'm sure they like them. Smiley-signs107
tackit, proud to be a member of MetalworkingFun Forum since May 2014.
Reply
Thanks given by:
tackit Offline
Sophmore
***
Posts: 125
Threads: 18
Joined: May 2014
Location: IN
#2,354
09-04-2014, 09:11 PM
(09-04-2014, 10:37 AM)dallen Wrote: been out in the back yard playing with the furnace again.

looks pretty good from this side


not so good from this side


but I know how to fix it, should of put a riser on the hub to feed back into the part when it cooled off, NiBrAl shrinks really bad in some castings.

DA

Got to hand it to you dallen, I would never been able to do that.
tackit, proud to be a member of MetalworkingFun Forum since May 2014.
Reply
Thanks given by:
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
#2,355
09-04-2014, 10:18 PM
(09-04-2014, 09:11 PM)tackit Wrote: Got to hand it to you dallen, I would never been able to do that.

Tackit it just takes a little knowledge and a whole bucketful of heat to do it.

Second try didn't turn out o good either, its got a big hot tear in it and what looks like some sand that washed out in the hub, so hopefully the fourth time will be the good one.

heres a shot of the second pour that I did today you can see the hot tear in it up against the hub.    

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
schor Offline
Sophmore
***
Posts: 190
Threads: 17
Joined: Aug 2014
Location: Ajax Ontario Canada
The following 5 users Like schor's post:
f350ca (09-05-2014), Mayhem (09-05-2014), stevec (09-05-2014), EdK (09-05-2014), Hawkeye (09-05-2014)
#2,356
09-04-2014, 10:51 PM
I made a tool holder holder.



Steve S
Check out MyShopNotes on youtube.
Reply
Thanks given by:
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
#2,357
09-05-2014, 05:49 AM (This post was last modified: 09-05-2014, 05:52 AM by stevec.)
That schor is nifty Blush Where were you when I made these?

   

   

   

   

Your idea epitomizes the k.i.s.s. principal.

Thumbsup

Smiley-eatdrink004
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by: schor
vtsteam Offline
Sophmore
***
Posts: 205
Threads: 3
Joined: Jul 2014
Location: Vermont
#2,358
09-05-2014, 11:05 AM
dallen, what is NiAlBr?
http://www.youtube.com/c/SRHacksaw
Reply
Thanks given by:
oldgoaly Offline
Junior
****
Posts: 251
Threads: 21
Joined: Jun 2013
Location: Shiloh, Il. USA
#2,359
09-05-2014, 12:22 PM
(09-04-2014, 10:37 AM)dallen Wrote: been out in the back yard playing with the furnace again.

but I know how to fix it, should of put a riser on the hub to feed back into the part when it cooled off, NiBrAl shrinks really bad in some castings.

DA

can you thicken the webbing from the center hub to the outer part of pulley? to me it looks like it's flowing thru the heavy sections not thru the thin.
oldgoaly, proud to be a member of MetalworkingFun Forum since Jun 2013.
Reply
Thanks given by:
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#2,360
09-05-2014, 01:20 PM
(09-05-2014, 11:05 AM)vtsteam Wrote: dallen, what is NiAlBr?

Nickel aluminum bronze?
Reply
Thanks given by:




Users browsing this thread: 15 Guest(s)